Abstract: This design idea explains how to implement an 8-bit analog-to-digital Converter (ADC), using a microcontroller
上傳時間： 2013-10-30
上傳用戶：愛死愛死
Abstract: The DS4830 optical microcontroller's analog-to-digital Converter (ADC) offset can change with temperature and gainselection. However, the DS4830 allows users to measure the ADC internal offset. The measured ADC offset is added to the ADCoffset register to nullify the offset error. This application note demonstrates the DS4830's ADC internal offset calibration in theapplication program.
上傳時間： 2014-12-23
上傳用戶：萍水相逢
Abstract: This tutorial discusses methods for digitally adjusting the output voltage of a DC-DC Converter. The digital adjustmentmethods are with a digital-to-analog Converter (DAC), a trim pot (digital potentiometer), and PWM output of a microprocessor.Each method is assessed and several DACs and digital potentiometers presented.
上傳時間： 2013-11-20
上傳用戶：zycidjl
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC Converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC Converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCConverter tolerances (27.6V to 36.7V).
上傳時間： 2014-12-23
上傳用戶：781354052
This paper presents a space vector modulation(SVM)-based switching strategy for a three-level neutral point clamped (NPC) Converter that is adapted as a STATCOM.
上傳時間： 2013-10-20
上傳用戶：zyt
The LTC®1966 is a true RMS-to-DC Converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC Converters. The LTC1966 RMS-to-DCConverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上傳時間： 2013-10-12
上傳用戶：qilin
This application note describes a Linear Technology "Half-Flash" A/D Converter, the LTC1099, being connected to a 256 element line scan photodiode array. This technology adapts itself to handheld (i.e., low power) bar code readers, as well as high resolution automated machine inspection applications..
上傳時間： 2013-11-21
上傳用戶：lchjng
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the Converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
標簽： Converters Defini DAC
上傳時間： 2013-10-30
上傳用戶：stvnash
1.2MHz 2A Synchronous Step-Down Converter
上傳時間： 2013-11-01
上傳用戶：qingzhuhu
返馳式(Flyback) 電源供應器是交換式電源設計供應器(Switch Power Supply，SPS)的一種，為工業界常用之電路架構，其特點如下表所示，圖一所示為返馳式轉換器(Flyback Converter)電路。 一般設計SPS需要一些保護來提高系統設備之穩定安全，尤其是輸出過電壓保護極為重要，這個輸出過電壓保護目的是防止電氣設備上的元件之絕緣遭受過電壓的破壞。一般過電壓的測試方法是將回授Open讓系統呈現段回路狀況，導致一次側能量無限制提供給二次測來達到輸出過電壓現象。
上傳時間： 2013-11-06
上傳用戶：haoxiyizhong
