富士通單片機MB902420系列
extINT Project:
All external Interrupt-Pins INT0 .. INT7 will be enabled.
A falling edge on INTx will toggle PDR4_P4x
in order to toggle the LEDx of the Flash-CAN-100P Board
e.g. falling edge on INT3 will result in LED D3 will toggleP47..P40 (UserLEDs of FlashCan100P)
and will send out again as byte-packages to ID#2
Receive-Buffer #1 : basic can
Transmit-Buffer #6 : full-can ID #2
vhdl編寫，8b—10b 編解碼器設計
Encoder:
8b/10b Encoder (file: 8b10b_enc.vhd)
Synchronous clocked inputs (latched on each clock rising edge)
8-bit parallel unencoded data input
KI input selects data or control encoding
Asynchronous active high reset initializes all logic
Encoded data output
10-bit parallel encoded output valid 1 clock later
Decoder:
8b/10b Decoder (file: 8b10b_dec.vhd)
Synchronous clocked inputs (latched on each clock rising edge)
10-bit parallel encoded data input
Asynchronous active high reset initializes all logic
Decoded data, disparity and KO outputs
8-bit parallel unencoded output valid 1 clock later
sfrmat is a Matlab function that provides a spatial frequency response* (SFR) from a digital image file containing a slanted-edge feature. The specific edge-gradient algorithm follows the intent of the standard ISO 12233, developed by Technical Committee ISI/TC 42, for resolution measurements for electronic still pictorial cameras.
Top module name : SHIFTER (File name : SHIFTER.v)
2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT.
3. Output pins: OUT [15:0].
4. Input signals generated from test pattern are latched in one cycle and are
synchronized at clock rising edge.
5. The SHIFT signal describes the shift number. The shift range is 0 to 15.
6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it
shifts input data to left.
7. When the signal SIGN is high, the input data is a signed number and it shifts with
sign extension. However, the input data is an unsigned number if the signal SIGN
is low.
8. You can only use following gates in Table I and need to include the delay
information (Tplh, Tphl) in your design.
Top module name : SHIFTER (File name : SHIFTER.v)
2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT.
3. Output pins: OUT [15:0].
4. Input signals generated from test pattern are latched in one cycle and are
synchronized at clock rising edge.
5. The SHIFT signal describes the shift number. The shift range is 0 to 15.
6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it
shifts input data to left.
7. When the signal SIGN is high, the input data is a signed number and it shifts with
sign extension. However, the input data is an unsigned number if the signal SIGN
is low.
8. You can only use following gates in Table I and need to include the delay
information (Tplh, Tphl) in your design.
ST32
基于（英蓓特）STM32V100的EXTI程序
This example shows how to configure an external interrupt line.
In this example, the EXTI line 9 is configured to generate an interrupt on each
falling edge. In the interrupt routine a led connected to PC.06 is toggled.
This led will be toggled due to the softawre interrupt generated on EXTI Line9
then at each falling edge.
selects the mux channel and configures the MAX197 for
second write pulse, written with ACQMOD = 0, termi-
either unipolar or bipolar input range. A write pulse (WR
nates acquisition and starts conversion on WR°Os risin
+ CS) can either start an acquisition interval or initiate a
edge (Figure 6). However, if the second control byte
combined acquisition plus conversion. The sampling
contains ACQMOD = 1, an indefinite acquisition interval
interval occurs at the end of the acquisition interval.
is restarted.
The ACQMOD bit in the input control byte offer
selects the mux channel and configures the MAX197 for
second write pulse, written with ACQMOD = 0, termi-
either unipolar or bipolar input range. A write pulse (WR
nates acquisition and starts conversion on WR°Os risin
+ CS) can either start an acquisition interval or initiate a
edge (Figure 6). However, if the second control byte
combined acquisition plus conversion. The sampling
contains ACQMOD = 1, an indefinite acquisition interval
interval occurs at the end of the acquisition interval.
is restarted.
The ACQMOD bit in the input control byte offer
selects the mux channel and configures the MAX197 for
second write pulse, written with ACQMOD = 0, termi-
either unipolar or bipolar input range. A write pulse (WR
nates acquisition and starts conversion on WR°Os risin
is restarted.
The ACQMOD bit in the input control byte offer+ CS) can either start an acquisition interval or initiate a
edge (Figure 6). However, if the second control byte
combined acquisition plus conversion. The sampling
contains ACQMOD = 1, an indefinite acquisition interval
interval occurs at the end of the acquisition interval.
97 law to enhance the classic procedure
Ridge wavelet extraction
Modulus maximum for the wavelet edge detection
Small spectral analysis method mallat classic procedure
