PCI（Peripheral Component Interconnect）局部總線是微型計算機中處理器、存儲器與外圍控制部件、擴展卡之間的互連接口，由于其速度快、可靠性高、成本低、兼容性好等特點，在各種計算機總線標準占有重要地位，基于PCI標準的接口設計已經成為相關項目開發中的一個重要的選擇。 目前，現場可編程門陣列FPGA（Field Programmable Gates）得到了廣泛應用。由于其具有規模大，開發過程投資小，可反復編程，且支持軟硬件協同設計等特點，因此已逐步成為復雜數字硬件電路設計的首選。 PCI接口的開發有多種方法，主要有兩種：一是使用專用接口芯片，二是使用可編程邏輯器件，如FPGA。本論文基于成本和實際需要的考慮，采用第二種方法進行設計。 本論文采用自上而下（Top-To-Down）和模塊化的設計方法，使用FPGA和硬件描述語言（VHDL和Verilog HDL）設計了一個PCI接口核，并通過自行設計的試驗板對其進行驗證。為使設計準確可靠，在具體模塊的設計中廣泛采用流水線技術和狀態機的方法。 論文最終設計完成了一個33M32位的PCI主從接口，并把它作為以NIOSⅡ為核心的SOPC片內外設，與通用計算機成功進行了通訊。 論文對PCI接口進行了功能仿真，仿真結果和PCI協議的要求一致，表明本論文設計正確。把設計下載進FPGA芯片EP2C8Q208C7之后，論文給出了使用SIGNALTAPⅡ觀察到的信號實際波形，波形顯示PCI接口能夠滿足本設計中系統的需要。本文最后還給出試驗板的具體設計步驟及驅動程序的安裝。
上傳時間： 2013-07-28
上傳用戶：372825274
以某高速實時頻譜儀為應用背景，論述了5 Gsps采樣率的高速數據采集系統的構成和設計要點，著重分析了采集系統的關鍵部分高速ADC（analog to digital，模數轉換器）的設計、系統采樣時鐘設計、模數混合信號完整性設計、電磁兼容性設計和基于總線和接口標準（PCI Express）的數據傳輸和處理軟件設計。在實現了系統硬件的基礎上，采用Xilinx公司ISE軟件的在線邏輯分析儀（ChipScope Pro）測試了ADC和采樣時鐘的性能，實測表明整體指標達到設計要求。給出上位機對采集數據進行處理的結果，表明系統實現了數據的實時采集存儲功能。
上傳時間： 2014-11-26
上傳用戶：黃蛋的蛋黃
In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. Note that this does not include the PowerPC 602ª microprocessor which has a multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is speciÞed for 32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32 bits,and ßoating-point data types of 32 and 64 bits (single-precision and double-precision).1.1 Overview The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI bus,and main memory. This section provides a block diagram showing the major functional units of the 106 and describes brießy how those units interact.Figure 1 shows the major functional units within the 106. Note that this is a conceptual block diagram intended to show the basic features rather than an attempt to show how these features are physically implemented on the device.
上傳時間： 2013-10-08
上傳用戶：18711024007
The Motorola MPC106 PCI bridge/memory controller provides a PowerPCªmicroprocessor common hardware reference platform (CHRPª) compliant bridgebetween the PowerPC microprocessor family and the Peripheral Component Interconnect(PCI) bus. In this document, the term Ô106Õ is used as an abbreviation for the phraseÔMPC106 PCI bridge/memory controllerÕ. This document contains pertinent physicalcharacteristics of the 106. For functional characteristics refer to theMPC106 PCI Bridge/Memory Controller UserÕs Manual.This document contains the following topics:Topic PageSection 1.1, ÒOverviewÓ 2Section 1.2, ÒFeaturesÓ 3Section 1.3, ÒGeneral ParametersÓ 5Section 1.4, ÒElectrical and Thermal CharacteristicsÓ 5Section 1.5, ÒPin AssignmentsÓ 17Section 1.6, ÒPinout Listings 18Section 1.7, ÒPackage DescriptionÓ 22Section 1.8, ÒSystem Design InformationÓ 24Section 1.9, ÒDocument Revision HistoryÓ 29Section 1.10, ÒOrdering InformationÓ 29
上傳時間： 2013-11-04
上傳用戶：as275944189
Express Mode uses an 8-bit wide bus path for fast configuration of Xilinx FPGAs. Thisapplication note provides information on how to perform Express configuration specifically forthe Spartan™-XL family. The Express mode signals and their associated timing are defined.The steps of Express configuration are described in detail, followed by detailed instructions thatshow how to implement the configuration circui
標簽： Spartan-XL Express XAPP FPGA
上傳時間： 2014-12-28
上傳用戶：hewenzhi
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and both implementation and simulation scripts
標簽： Transceiver Virtex Wizar GTP
上傳時間： 2013-10-23
上傳用戶：leyesome
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
上傳時間： 2013-11-05
上傳用戶：Wwill
The PCI Special Interest Group disclaims all warranties and liability for the use of this document and the information contained herein and assumes no responsibility for any errors that may appear in this document, nor does the PCI Special Interest Group make a commitment to update the information contained herein.
上傳時間： 2013-11-01
上傳用戶：KSLYZ
PCI Express是由Intel，Dell，Compaq，IBM，Microsoft等PCI SIG聯合成立的Arapahoe Work Group共同草擬并推舉成取代PCI總線標準的下一代標準。PCI Express利用串行的連接特點能輕松將數據傳輸速度提到一個很高的頻率，達到遠遠超出PCI總線的傳輸速率。一個PCI Express連接可以被配置成x1，x2，x4，x8，x12，x16和x32的數據帶寬。x1的通道能實現單向312.5 MB／s（2.5 Gb／s）的傳輸速率。Xilinx公司的Virtex5系列FPGA芯片內嵌PCI-ExpressEndpoint Block硬核，為實現單片可配置PCI-Express總線解決方案提供了可能?！ ”疚脑谘芯縋CI-Express接口協議和PCI-Express Endpoint Block硬核的基礎上，使用Virtex5LXT50 FPGA芯片設計PCI Express接口硬件電路，實現PCI-Express數據傳輸
上傳時間： 2013-12-27
上傳用戶：wtrl
Express Mode uses an 8-bit wide bus path for fast configuration of Xilinx FPGAs. Thisapplication note provides information on how to perform Express configuration specifically forthe Spartan™-XL family. The Express mode signals and their associated timing are defined.The steps of Express configuration are described in detail, followed by detailed instructions thatshow how to implement the configuration circui
標簽： Spartan-XL Express XAPP FPGA
上傳時間： 2015-01-02
上傳用戶：nanxia
