磁芯電感器的諧波失真分析 摘 要：簡述了改進鐵氧體軟磁材料比損耗系數和磁滯常數ηB，從而降低總諧波失真THD的歷史過程，分析了諸多因數對諧波測量的影響，提出了磁心性能的調控方向。 關鍵詞：比損耗系數， 磁滯常數ηB ，直流偏置特性DC-Bias，總諧波失真THD Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033 Abstract: Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward. Key words: ratio loss coefficient，hysteresis constant，DC-Bias，THD 近年來，變壓器生產廠家和軟磁鐵氧體生產廠家，在電感器和變壓器產品的總諧波失真指標控制上，進行了深入的探討和廣泛的合作，逐步弄清了一些似是而非的問題。從工藝技術上采取了不少有效措施，促進了質量問題的迅速解決。本文將就此熱門話題作一些粗淺探討。 一、 歷史回顧 總諧波失真（Total harmonic distortion） ，簡稱THD，并不是什么新的概念，早在幾十年前的載波通信技術中就已有嚴格要求<1>。1978年郵電部公布的標準YD/Z17－78“載波用鐵氧體罐形磁心”中，規定了高μQ材料制作的無中心柱配對罐形磁心詳細的測試電路和方法。如圖一電路所示，利用LC組成的150KHz低通濾波器在高電平輸入的情況下測量磁心產生的非線性失真。這種相對比較的實用方法，專用于無中心柱配對罐形磁心的諧波衰耗測試。 這種磁心主要用于載波電報、電話設備的遙測振蕩器和線路放大器系統，其非線性失真有很嚴格的要求。
圖中 ZD —— QF867 型阻容式載頻振蕩器，輸出阻抗 150Ω， Ld47 —— 47KHz 低通濾波器，阻抗 150Ω，阻帶衰耗大于61dB， Lg88 ——并聯高低通濾波器，阻抗 150Ω，三次諧波衰耗大于61dB Ld88 ——并聯高低通濾波器，阻抗 150Ω，三次諧波衰耗大于61dB FD —— 30～50KHz 放大器， 阻抗 150Ω， 增益不小于 43 dB，三次諧波衰耗b3(0)≥91 dB, DP —— Qp373 選頻電平表，輸入高阻抗， L ——被測無心罐形磁心及線圈， C ——聚苯乙烯薄膜電容器CMO-100V-707APF±0.5%,二只。
測量時，所配用線圈應用絲包銅電磁線SQJ9×0.12(JB661-75)在直徑為16.1mm的線架上繞制 120 匝， （線架為一格） ， 其空心電感值為 318μH（誤差1％） 被測磁心配對安裝好后，先調節振蕩器頻率為 36.6～40KHz， 使輸出電平值為+17.4 dB， 即選頻表在 22′端子測得的主波電平 （P2）為+17.4 dB，然后在33′端子處測得輸出的三次諧波電平（P3）， 則三次諧波衰耗值為：b3(+2)= P2+S+ P3 式中：S 為放大器增益dB 從以往的資料引證， 就可以發現諧波失真的測量是一項很精細的工作，其中測量系統的高、低通濾波器，信號源和放大器本身的三次諧波衰耗控制很嚴，阻抗必須匹配，薄膜電容器的非線性也有相應要求。濾波器的電感全由不帶任何磁介質的大空心線圈繞成，以保證本身的“潔凈” ，不至于造成對磁心分選的誤判。 為了滿足多路通信整機的小型化和穩定性要求， 必須生產低損耗高穩定磁心。上世紀 70 年代初，1409 所和四機部、郵電部各廠，從工藝上改變了推板空氣窯燒結，出窯后經真空罐冷卻的落后方式，改用真空爐，并控制燒結、冷卻氣氛。技術上采用共沉淀法攻關試制出了μQ乘積 60 萬和 100 萬的低損耗高穩定材料，在此基礎上，還實現了高μ7000～10000材料的突破，從而大大縮短了與國外企業的技術差異。當時正處于通信技術由FDM（頻率劃分調制）向PCM（脈沖編碼調制） 轉換時期， 日本人明石雅夫發表了μQ乘積125 萬為 0.8×10 ，100KHz）的超優鐵氧體材料<3>，其磁滯系數降為優鐵
Abstract: The rapid build out of today's smart grid raises a number of security questions. In this article,we review two recent well-documented security breaches and a report of a security gap. These situationsinclude a 2009 smart-meter hack in Puerto Rico; a 2012 password discovery in grid distributionequipment; and insecure storage of a private key in distribution automation equipment. For each of theseattacks, we examine the breach, the potential threat, and secure silicon methods that, as part of acomplete security strategy, can help thwart the attacks.
Abstract: Stuxnet, a sophisticated virus that damaged Iran's nuclear capability, should be an eye openerfor the world. We can choose to learn something very narrow (how to combat the Stuxnet virus) or wecan choose to focus on the larger goal of thwarting the next type of creative cyber attack. Unfortunately,critical industrial infrastructure is not currently designed with security as a key goal, leaving open multipleavenues for an educated and funded attacker to create massive problems. This tutorial outlines somebasic concepts that engineers and product definers should consider to make sure their new projects stayahead of future threats.
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
Handheld electronic devices play a key role in our everydaylives. Because dependability is paramount, handhelds arecarefully engineered with lightweight power sources forreliable use under normal conditions. But no amount ofcareful engineering can prevent the mistreatment theywill undergo at the hands of humans. For example, whathappens when a factory worker drops a bar code scanner,causing the battery to pop out? Such events areelectronically unpredictable, and important data storedin volatile memory would be lost without some form ofsafety net—namely a short-term power holdup systemthat stores suffi cient energy to supply standby power untilthe battery can be replaced or the data can be stored inpermanent memory.
光伏發電是未來新能源發電重要方向之一，而光伏變流器是光伏發電系統的核心。介紹一種基于微網理念的光伏變流器設計。以該變流器為核心的光伏發電系統可以看做一個小型的微網系統。該系統能根據外部電網情況，工作于并網模式和離網模式。介紹了該系統的各個組成部件的設計以及變流器主電路部分器件的選型。最后，由實驗樣機進行測試。試驗結果驗證了電路拓撲結構及控制方案的可行性，也說明了系統參數設計方法的正確性。
Abstract:
Solar Photovoltaic generation is an important direction of new energy power generation in the future，while photovoltaic converter is the core of photovoltaic generation system. This paper deals with a study on photovoltaic inverter based on the concept of microgrid. This paper describes a system whose core component is the photovoltaic inverter，can work on grid-connected mode or run independently according to the external situation. The paper simply describes the main components of the system. At last，the prototype was produced and tested. Test result has proved feasibility of circuit topology structure and controlling scheme and shown correctness of system parameters.Key words: PV inverter； microgrid； off-grid； storage battery
This white paper raises some fundamental issues the design engineer should address before deciding upon a communication approach for a wireless network. As no universal wireless network solution exists, it should be custom tailored to suit the application demands. Defining your application communication characteristics is the key to ensure optimal communication reliability and resistance to interfering noise sources.
