Virtex-5, Spartan-DSP FPGAs Application Note This application note demonstrates how efficient implementations of Digital Up Converters(DUC) and Digital Down Converters (DDC) can be done by leveraging the Xilinx DSP IPportfolio for increased productivity and reduced time to development. Step-by-step instruction is given on how to perform system-level trade off analysis and develop the most efficient FPGA implementation, thus allowing engineers a flexible, low-cost and low-power alternative to ASSP technologies.
標簽： Spartan-DSP Virtex FPGAs Ap
上傳時間： 2013-10-23
上傳用戶：raron1989
The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
上傳時間： 2013-11-16
上傳用戶：浩子GG
MC9S08QG8英文資料 The MC9S08QG8 is the newest member of the Freescale 8-bit family of highly integratedmicrocontrollers, based on the high-performance yet low power HCS08 core. The MC9S08QG8is an excellent solution for power-sensitive applications with extended battery life and maximum performance down to 1.8VDC.
上傳時間： 2014-12-28
上傳用戶：dxxx
Using the XGATE for Manchester DecodingTable of Contents 1 Introduction 1.1 XGATE Module in S12X 2 Decoding Algorithm 3 Software Implementation 3.1 Frame Scheme 3.2 Operating Modes and Demo 3.3 Files Summary 3.4 Complete Mode Flowchart 4 Manchester Encoder 4.1 Devices Used 5 Conclusion Appendix A Noise Elements During RF Transmissions in the Manchester Decoding ImplementationA.1 Types of Noise A.2 Effects of Noise A.3 Workaround for Noise Effects
標簽： Manchester XGATE 譯碼
上傳時間： 2013-10-15
上傳用戶：wqq123456
1、 支持USB 1.1通訊協議；2、 支持高速（Full Speed、12Mbps ）和低速（Low Speed、1.5Mbps ）傳輸；3、 6MHz晶體，鎖相環PLL振蕩器提供高速、低速所需時鐘源；4、 支持3個端口（endpoint），可獨立編程為IN 或 OUT端口。5、 PS/2：支持PS/2協議（eg.鼠標），與USB復用。
上傳時間： 2013-11-03
上傳用戶：hbsunhui
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
上傳時間： 2013-10-10
上傳用戶：inwins
The PCA9517 is a CMOS integrated circuit that provides level shifting between lowvoltage (down to 0.9 V) and higher voltage (2.7 V to 5.5 V) I2C-bus or SMBus applications.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling two buses of 400 pF. Usingthe PCA9517 enables the system designer to isolate two halves of a bus for both voltageand capacitance. The SDA and SCL pins are over voltage tolerant and arehigh-impedance when the PCA9517 is unpowered.
標簽： translating Level 9517 PCA
上傳時間： 2013-12-25
上傳用戶：wsf950131
The PCA9519 is a 4-channel level translating I2C-bus/SMBus repeater that enables theprocessor low voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBusmaximum capacitance of 400 pF on the higher voltage side. The SDA and SCL pins areover-voltage tolerant and are high-impedance when the PCA9519 is unpowered.
標簽： 4channel transla level 9519
上傳時間： 2013-11-19
上傳用戶：jisiwole
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
標簽： 4channel multiple 9544A 9544
上傳時間： 2014-12-28
上傳用戶：潛水的三貢
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上傳時間： 2014-11-22
上傳用戶：xcy122677
