特點（FEATURES） 精確度0.1%滿刻度（Accuracy 0.1%F.S.） 多種輸入輸出選擇（Wide selection of input/output range） 輸入與輸出1/輸出2絕緣耐壓 2仟伏特/1分鐘（Dielectric strength 2KVac/1min.（input/output1/output2）） 寬范圍交直流兩用電源設計（Wide input range for auxiliary power） 尺寸小，穩定性高（Dimension small & High stability）
特點（FEATURES） 精確度0.03%滿刻度（Accuracy 0.03%F.S.） 頻率輸入范圍0.01Hz至80KHz（Input range from 0.01 Hz to 80KHz） 16 BIT 隔離類比輸出（16 bit DAC isolating analog output） 輸入與輸出1/輸出2絕緣耐壓 2仟伏特/1分鐘（Dielectric strength 2KVac/1min.（input/output1/output2）） 寬范圍交直流兩用電源設計（Wide input range for auxiliary power） 尺寸小，穩定性高（Dimension small & High stability）
特點(FEATURES) 精確度0.1%滿刻度 (Accuracy 0.1%F.S.) 可作各式數學演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 類比輸出功能(16 bit DAC isolating analog output function) 輸入/輸出1/輸出2絕緣耐壓2仟伏特/1分鐘(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 寬范圍交直流兩用電源設計(Wide input range for auxiliary power) 尺寸小,穩定性高(Dimension small and High stability)
針對TI公司最新發布的TMS320C6678 DSP設計出一種實用有效的電源。采用統一的12 V電源供電，制作出滿足電壓幅值要求與時序要求的開關電源。該設計主要由各類電源轉換電路組成，并通過使用Fusion Digital Power Designer軟件對電源芯片進行編程。仿真結果表明，該電源工作穩定，各方面的參數均符合要求。
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
有源功率因數校正可減少用電設備對電網的諧波污染，提高電器設備輸入端的功率因數。詳細分析了有源功率因數校正APFC（active power factor corrector）原理，采用平均電流控制模式控制原理，設計了基于UC3854BN芯片的一種有源功率因數校正電路方案，著重分析了電路主要參數的選擇和設計。實踐證明，采用APFC后，大大減小了輸入電流的諧波分量，實現了功率因數校正。
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
