簡單介紹了三相SPWM逆變器的組成和工作原理，通過計算機對三相SPWM逆變器進行Matlab/Simulink建模和仿真，研究逆變電路的輸入輸出及其特性。仿真分析經逆變后得到的電壓電流的特性。通過運用Matlab/Simulink和Power System Block（PSB）電力系統模塊集工具箱仿真環境，對電路進行建模、計算和仿真分析。MATLAB軟件中的Simulink，是為數不多的完全滿足這些條件和要求的軟件。并且憑借他在科學計算方面的天然優勢建立了從設計構思到最終實現設計要求的可視化橋梁。被廣泛應用于線性系統、非線性系統及數字信號處理的建模和仿真中。
上傳時間： 2013-11-12
上傳用戶：yulg
We provide complete power solutions with a full lineup of power managementproducts. This brochure provides an overview of our high performance DC/DC switching regulatorcontrollers for applications including datacom, telecom, industrial, automotive, medical, avionicsand control systems. We make power design easier with our industry-leading field applicationengineering support; a broad selection of demonstration boards with schematics, layout filesand parts lists; SwitcherCAD® software for simulation, application notes and comprehensivetechnical documentation.
上傳時間： 2013-10-15
上傳用戶：lz4v4
In industrial applications, high voltage power supply spikes with durations ranging from a few microseconds to hundreds of millisecondsare commonly encountered. The electronics in these systems must not only survive transient voltage spikes, but in many cases alsooperate reliably throughout the event.
上傳時間： 2013-11-07
上傳用戶：redmoons
返馳式(Flyback) 電源供應器是交換式電源設計供應器(Switch Power Supply，SPS)的一種，為工業界常用之電路架構，其特點如下表所示，圖一所示為返馳式轉換器(Flyback Converter)電路。 一般設計SPS需要一些保護來提高系統設備之穩定安全，尤其是輸出過電壓保護極為重要，這個輸出過電壓保護目的是防止電氣設備上的元件之絕緣遭受過電壓的破壞。一般過電壓的測試方法是將回授Open讓系統呈現段回路狀況，導致一次側能量無限制提供給二次測來達到輸出過電壓現象。
上傳時間： 2013-11-06
上傳用戶：haoxiyizhong
計算機的ATX電源脫離主板是需要短接一下20芯接頭上的綠色（power on）和黑色（地）才能啟動的。啟動后把萬用表撥到主流電壓20V檔位，把黑表筆插入4芯D型插頭的黑色接線孔中，用紅表筆分別測量各個端子的電壓。樓上列的是20芯接頭的端子電壓，4芯D型插頭的電壓是黃色＋12V，黑色地，紅色＋5V。 主板電源接口 圖解 20-PIN ATX主板電源接口
上傳時間： 2013-10-28
上傳用戶：蔣清華嗯
Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.
上傳時間： 2013-11-20
上傳用戶：feitian920
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上傳時間： 2013-11-18
上傳用戶：zhouxuepeng1
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
上傳時間： 2013-10-12
上傳用戶：jinyao
基于輸入28.5 VDC，輸出總功率180 W的機載計算機電源的設計，為滿足“GJB181飛機供電特性”中對飛機用電設備輸入28.5 VDC時過壓浪涌80 V/50ms的要求，采用檢測輸入電壓并控制MOSFET導通和關斷的方法，通過對該電路的理論數據分析及與實際測試數據做比較，模擬了80 V/50 ms過壓浪涌的試驗，并用示波器記錄了測試波形，得出該設計電路在輸入28.5 VDC時，可以完全滿足GJB181飛機供電特性過壓浪涌要求的結論。并通過擴展應用介紹了在其他輸入電壓類型時過壓浪涌保護電路的設計。
上傳時間： 2013-10-18
上傳用戶：cuibaigao
Abstract: Nonideal cable dispersive effects can affect system performance. This application note discusses the twomain loss effects related to cables (skin-effect and dielectric losses), and presents a simple method of modeling thecable for use in standard SPICE simulators.
上傳時間： 2014-11-18
上傳用戶：wxnumen
