This application note is intended for system designers who require a hardware
implementation overview of the development board features such as the power supply, the
clock management, the reset control, the boot Mode settings and the debug management. It
shows how to use the High-density and Medium-density STM32F10xxx product families and
describes the minimum hardware resources required to develop an STM32F10xxx
application.
Abstract: This application note describes how to design boost converters using the MAX17597 peakcurrent-Mode controller. Boost converters can be operated in discontinuous conduction Mode (DCM) orcontinuous conduction Mode (CCM). This operating Mode can affect the component choices, stress levelin power devices, and controller design. Formulas for calculating component values and ratingsare alsopresented.
交流功率因數轉換器 特點： 精確度0.25%滿刻度 ±0.25o 多種輸入,輸出選擇 輸入與輸出絕緣耐壓2仟伏特/1分鐘 沖擊電壓測試5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波電壓測試2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，穩定性高 主要規格： 精確度: 0.25% F.S. ±0.25°(23 ±5℃) 輸入負載: <0.2VA (Voltage) <0.2VA (Current) 最大過載能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2 x rated continuous 輸出反應速度: < 250ms(0~90%) 輸出負載能力: < 10mA for voltage Mode < 10V for current Mode 輸出之漣波: < 0.1% F.S. 歸零調整范圍: 0~ ±5% F.S. 最大值調整范圍: 0~ ±10% F.S. 溫度系數: 100ppm/℃ (0~50℃) 隔離特性: Input/Output/Power/Case 絕緣抗阻: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power/case) 突波測試: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV(1.2x50us) 使用環境條件: -20~60℃(20 to 90% RH non-condensed) 存放環境條件: -30~70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
交流電壓，電流轉換器 特點： 精確度0.25%滿刻度(RMS) 多種輸入,輸出選擇 輸入與輸出絕緣耐壓2仟伏特/1分鐘 沖擊電壓測試5仟伏特(1.2x50us) (IEC255-4,ANSI C37.90a/1974) 突波電壓測試2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，穩定性高 2:主要規格 精確度:0.25%F.S.(RMS) (23 ±5℃) 輸入負載: <0.2VA(voltage) <0.2VA(current) 最大過載能力: Current related input:3 x rated continuous 10 x rated 30 sec. ,25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2x rated continuous 輸出反應時間: <250ms (0~90%) 輸出負載能力: <10mA for voltage Mode <10V for current Mode 輸出漣波: <0.1% F.S. 歸零調整范圍: 0~±5% F.S. 最大值調整范圍: 0~±10% F.S. 溫度系數: 100ppm/℃ (0~50℃) 隔離特性: Input/Output/Power/Case 絕緣抗阻: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 行動測試: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV (1.2 x 50us) 突波測試: 2.5KV-0.25ms/1MHz 使用環境條件: -20~60℃(20 to 90% RH non-condensed) 存放環境條件: -30~70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
Abstract: Alexander Graham Bell patented twisted pair wires in 1881. We still use them today because they work so well. In addition we have the advantage ofincredible computer power within our world. Circuit simulators and filter design programs are available for little or no cost. We combine the twisted pair and lowpassfilters to produce spectacular rejection of radio frequency interference (RFI) and electromagnetic interference (EMI). We also illustrate use of a precision resistorarray to produce a customizable differential amplifier. The precision resistors set the gain and common Mode rejection ratios, while we choose the frequencyresponse.
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonMode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon Mode voltage.
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-Mode ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
