主要介紹構成記憶示波器的STC12C5408AD增強型單片機8通道10位模數轉換功能的設置、應用和具體的匯編程序設計，以及PC機串行通訊和圖形顯示的高速匯編程序的設計要點，并列舉實例說明其應用效果。
Abstract:
The configuration, applications and the designs for? compiling program of the memorial oscillograph of 10 bits A/D conversation are introduced. It’s bases on STC12C5408AD 8? channels? single-chip? computer? in? enhancement? Mode. It also recommends the devising essentials of high speed compiling program for PC serial communication and graphics display, lists examples to explain its effects in using.
基于幅移鍵控技術ASK（Amplitude-Shift Keying），以C8051F340單片機作為監測終端控制器，C8051F330D單片機作為探測節點控制器，采用半雙工的通信方式，通過監控終端和探測節點的無線收發電路，實現數據的雙向無線傳輸。收發電路采用直徑為0.8 mm的漆包線自行繞制成圓形空心線圈天線，天線直徑為（3.4±0.3）cm。試驗表明，探測節點與監測終端的通信距離為24 cm，通過橋接方式，節點收發功率為102 mW時，節點間的通信距離可達20 cm。與傳統無線收發模塊相比，該無線收發電路在受體積、功耗、成本限制的場合有廣闊的應用前景。
Abstract:
Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication Mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
將現行的供暖計費方式由按建筑面積計費變為按消耗的熱能計費是供暖計費方式發展趨勢，為了滿足這一計費方式變化的需要，設計了基于IC卡的預付費式新型供暖計費系統，通過測量用戶采暖系統進出口的溫度和流量，計算用戶消耗的熱能，利用IC卡記錄用戶預付費的金額和當年熱能的單價，根據熱能消耗和當年熱能的單價計算用戶采暖費，根據實際發生的供暖費用和預付費金額控制供暖的開停，這一計費方式的變化使供暖計費更趨合理。
Abstract:
It is trend that the Mode of heat charging is changed from billing by building area to by thermal energy. In order to meet the needs of heat charging Mode changing， a new system of heat charging based on IC card is proposed. The user?蒺s energy consumption is calculated by measuring the user inlet and outlet temperature and flow，using the IC card to record the prepaid amount and the current price of heat. The user?蒺s heating costs is calculated according to energy consumption and current price， according to actual heating costs and prepaid amount，the system controls the heating opening or stopping. It is more reasonable that calculated heating costs by user heat consumption
The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-Mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
The PCA9674/74A provide general purpose remote I/O expansion for most
microcontroller families via the two-line bidirectional bus (I2C-bus) and is a part of the
Fast-Mode Plus (Fm+) family.
Using the XGATE for Manchester DecodingTable of Contents
1 Introduction 1.1 XGATE Module in S12X 2 Decoding Algorithm 3 Software Implementation 3.1 Frame Scheme 3.2 Operating Modes and Demo 3.3 Files Summary 3.4 Complete Mode Flowchart 4 Manchester Encoder 4.1 Devices Used 5 Conclusion Appendix A Noise Elements During RF Transmissions in the Manchester Decoding ImplementationA.1 Types of Noise A.2 Effects of Noise A.3 Workaround for Noise Effects
