介紹一種基于C8051單片機的動態心電監護系統。該系統由兩部分組成：以C8051F320單片機為核心的數據采集裝置和以PC機為平臺的分析處理系統。硬件電路功耗低，由單片機自帶的USB接口將數據傳送給PC機。軟件平臺采用LabVIEW可視化虛擬儀器系統開發平臺，將傳統儀器的功能模塊集成到計算機中，用戶可通過修改虛擬儀器的程序改變其功能。采用USB接口實時傳輸心電數據，并將數據采集模塊設計為計算機外設，使該系統高速快捷、小巧便攜。
Abstract:
In this design，a low-cost ECG electrocardiogram monitoring system is introduced，which consists of two parts:data acquisition device based on C8051F320and PC terminal as the analysis and processing system.The system is low-power consumption，the data is transmitted to the PC terminal by USB interface of the C8051F320.By using the visible virtual instrument system developing platform LabVIEW，the traditional instruments function Modules are integrated into the computer，so the user can modify virtual instrument software to change its function to meet their needs.Using USB in-terface to realize real-time ECG data transmission，in addition，ECG data acquisition module is designed as the computer peripheral，which makes the syetem high-speed and portable.
提出一種基于C8051F040的炮塔方位角測試系統的設計方案，給出測試系統的各個模塊軟硬件設計。炮塔方位角測試系統集數據采集，數據傳輸和數據顯示等功能于一體，實現了炮塔方位角裝置的離線檢測。系統軟件采用C51編寫，對單片機進行有效電源管理，保證了系統的穩定性，可靠性。
Abstract:
This paper puts forwards a design of artillery position system based on C8051F040，describes all Modules hardware and software design of measurement system.The system has the function of information collection，transmission，and display.It can measure artillery position system in offline.The system software using C51can manage the power of single chip microcomputer，guarantee the stability，reliability.
介紹基于VHDL的微型打印機控制器的設計。論述了微型打印機的基本原理，以及實現控制器的VHDL語言設計。打印機的數據來自系統中的存儲模塊，根據需要控制打印。該微型打印機控制器可取代傳統的微型打印機,且抗干擾性好,可靠性高，具有較強的移植性，稍加改動就可應用于不同場合。
Abstract:
This paper introduced the design method of micro printer controller based on VHDL.The basic principles of microprinter is explained,as well as the realization of the controller by VHDL language.The printer data is from the system memory Modules,can control printer.The design of microprinter controller has antigood and high reliability，it can replace the traditional printer.The controller has very good portability,and need little modify that can use in different situation.
介紹一種采用單片機技術和基站器件EM4095的手持式低頻RFID讀卡器方案。首先對整個系統框架進行說明，然后介紹主要功能模塊的設計，給出了各模塊的原理圖。重點描述了基站器件EM4095的性能參數和功能原理，最后描述了該系統的主程序流程圖。
Abstract:
In this paper,a handheld RFID reader based on MCU and EM4095 is introduced.At first，the configuration of this system is explained.Then the design of main Modules and schematic documents are particularly presented.The parameters and principle of the chip EM4095 are introduced in detail. At last，the main software flow is given
提出了一種基于C8051F320的列車安全巡檢儀的設計方案，詳細闡述了巡檢儀的各個模塊的硬、軟件設計。巡檢儀集信息采集、軸溫檢測、照明和記錄存儲等功能于一體，實現了對列車安全巡檢工作有效的監督和科學管理。系統軟件采用C51編寫，對單片機進行有效的電源管理，保證了巡檢儀的穩定性、可靠性和低功耗性。
Abstract:
This paper puts forward a design of train safety inspection based on C8051F320,describes all Modules hardware and software design of inspection instrument.The inspection instrument has the function of information collection, axle’s temperature detection, lighting and records storage.It can supervise and administer train safety inspection work effectively.The system software using C51 can manage the power of single chip microcomputer, and guarantee the stability, reliability and low power consumption of the inspection instrument.
基于幅移鍵控技術ASK（Amplitude-Shift Keying），以C8051F340單片機作為監測終端控制器，C8051F330D單片機作為探測節點控制器，采用半雙工的通信方式，通過監控終端和探測節點的無線收發電路，實現數據的雙向無線傳輸。收發電路采用直徑為0.8 mm的漆包線自行繞制成圓形空心線圈天線，天線直徑為（3.4±0.3）cm。試驗表明，探測節點與監測終端的通信距離為24 cm，通過橋接方式，節點收發功率為102 mW時，節點間的通信距離可達20 cm。與傳統無線收發模塊相比，該無線收發電路在受體積、功耗、成本限制的場合有廣闊的應用前景。
Abstract:
Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver Modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
針對船舶氣象儀保障維修而設計的船舶氣象儀測試系統，包括信息處理終端、主儀器檢測模塊、傳感器檢測模塊，各個模塊都采用基于AVR單片機的嵌入式系統，模塊之間通過CAN總線進行通信。結果表明，船舶氣象儀測試系統能夠快速檢測船舶氣象儀故障，與單純依靠人工方式排查故障相比，故障檢測時間縮短了60%以上。
Abstract:
The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these Modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
MPLAB C30用戶指南(英文)
HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support
Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language Modules.
The Controller Area Network (CAN) is a serial, asynchronous, multi-master communication protocol forconnecting electronic control Modules, sensors and actuators in automotive and industrial applications.With the SJA1000, Philips Semiconductors provides a stand-alone CAN controller which is more than a simpleeplacement of the PCA82C200.Attractive features are implemented for a wide range of applications, supporting system optimization, diagnosisand maintenance.
基于LabVIEW和單片機的空調溫度場測量系統的研究:室內溫度是空調系統舒適性的重要指標,對其及時、準確地測量顯得非常重要。介紹單片機AT89C51 和數字式、單總線型溫度傳感器DS18B20 組成矩形測量網絡采集空調室內40 點溫度,LabVIEW作為開發平臺,二者之間通過串口實現數據通信,利用LabVIEW強大的數據處理和顯示功能對采集的空調溫度場數據進行實時處理、分析和顯示,詳細介紹了系統的硬件結構和軟件模塊的設計方案。關鍵詞:單片機;DS18B20 ;LabVIEW;串行通信
Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software Modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
