A frequent requirement in systems involves drivinganalog signals into non-linear or reactive loads. Cables,transformers, actuators, motors and sample-hold circuitsare examples where the ability to drive diffi cult loads isrequired. Although several power buffer amplifi ers areavailable, none have been optimized for driving diffi cultloads.
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
SRAM-based FPGAs are non-volatile devices. Upon powerup, They are required to be programmed from an external source. This procedure allows anyone to easily monitor the bit-stream, and clone the device. The problem then becomes how can you effectively protect your intellectual property from others in an architecture where the part is externally programmed?
特點 最高輸入頻率 10KHz 顯示范圍0-9999（一段設定）0至999999累積量 計數速度 50/10000脈波/秒可選擇 輸入脈波具有預設刻度功能 累積量同步（批量）或非同步（批次）計數可選擇 數位化指撥設定操作簡易 計數暫時停止功能 1組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: 0-9999（PV,SV） 0-999999(TV) 顯示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
特點 顯示值范圍-199999至999999位數 最高輸入頻率 5KHz 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 定位基準值可任意設定 比較磁滯值可任意設定 數位化指撥設定操作簡易 3組繼電器輸出功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <5KHz 定位置范圍: -199999 to 999999 second adjustabl 比較磁滯范圍: 0 to 9999 adjustable 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 顯示幕: Red high efficiency LEDs high 9.2mm (.36") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
特點 精確度0.25%滿刻度 ±1位數 輸入配線系統可任意選擇 CT比可任意設定 具有異常電流值與異常次數記錄保留功能 電流過高或過低檢測可任意設定 報警繼電器復歸方式可任意設定 尺寸小,穩定性高 2.主要規格 輔助電源: AC110V&220V ±20%(50 or 60Hz) AC220V&440V ±20%(50 or 60Hz)(optional) 精確度: 0.25% F.S. ±1 digit 輸入負載: <0.2VA (Current) 最大過載能力 : Current related input: 2 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1 sec. 輸入電流范圍: AC0-5A (10-1000Hz) CT ratio : 1-2000 adjustable 啟動延遲動作時間: 0-99.9 second adjustable 繼電器延遲動作時間: 0-99.9 second adjustable 繼電器復歸方式: Manual (N) / latch(L) can be modified 繼電器磁滯范圍: 0-999 digit adjustable 繼電器動作方向: HI /LO/GO/HL can be modified 繼電器容量: AC 250V-5A, DC 30V-7A 過載顯示: "doFL" 溫度系數: 50ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 14.22mm(.276")(NO) 參數設定方式: Touch switches 記憶型式 : Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用環境條件 : 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
特點 精確度0.1%滿刻度 ±1位數 可量測 交直流電流/交直流電壓/電位計/傳送器/Pt-100/荷重元/電阻 等信號 顯示范圍-1999-9999可任意規劃 具有異常值與異常次數記錄保留功能 異常信號過高或過低或范圍內或范圍外檢測可任意設定 報警繼電器復歸方式可任意設定 尺寸小,穩定性高 2.主要規格 精確度: 0.1% F.S. ±1 digit 0.2% F.S. ±1 digit(AC) 取樣時間: 16 cycles/sec. 顯示值范圍: -1999 - +9999 digit adjustable 啟動延遲動作時間: 0-99.9 second adjustable 繼電器延遲動作時間: 0-99.9 second adjustable 繼電器復歸方式: Manual (N) / latch(L) can be modified 繼電器動作方向: HI /LO/GO/HL can be modified 繼電器容量: AC 250V-5A, DC 30V-7A 過載顯示: "doFL" 溫度系數: 50ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 7.0mm(.276")(NO) 參數設定方式: Touch switches 記憶型式 : Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用環境條件 : 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 計數暫時停止功能 3組報警功能 15BIT類比輸出功能 數位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 類比輸出解析度: 15 bit DAC 輸出反應速度: < 1/f+10ms(0-90%) 輸出負載能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 輸出之漣波: < 0.1% F.S. 通訊位址: "01"-"FF" 傳輸速度: 19200/9600/4800/2400 selective 通信協議: Modbus RTU mode 顯示幕: Red high efficiency LEDs high 14.22mm (.56") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 前置量設定功能(二段設定)可選擇 數位化指撥設定操作簡易 計數暫時停止功能 3組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <5KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 顯示幕: Red high efficiency LEDs high 9.2mm (.36") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) ( 感應器電源 ) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
