設計了自動控制系統綜合實驗案例“基于LabVIEW和單片機的溫度控制系統設計”。實驗系統硬件部分由單片機、溫度傳感器、D/A轉換模塊、調壓模塊和電烤箱組成,設計了單片機與各個模塊之間的接口電路。軟件部分采用LabVIEW軟件實現控制算法,并設計監控界面實現參數設定、溫度數據實時監控等功能。設計了單片機與LabVIEW軟件之間的串口通信程序,實現了輸入、輸出數據的傳輸。通過綜合實驗系統設計,使學生得到控制系統設計和實驗調試等綜合能力的訓練。A comprehensive experimental case of the automatic control system is presented,which is the design of the temperature control system based on LabVIEW and SCM.The hardware part of the experimental system is composed of the SCM,temperature sensor,D/A conversion module,voltage regulating module and electric oven.The interface circuit between the SCM and each module is designed.In the software part,LabVIEW software is used to realize the control algorithm,and the monitoring interface is designed to realize the functions of parameter setting,temperature data real-time monitoring,etc.The serial communication program between the SCM and LabVIEW software is designed to realize the transmission of input and OUTPUT data.Through the design of this comprehensive experimental system,students can get the comprehensive ability training for the control system design,experiment debugging,etc.
上傳時間： 2022-03-27
上傳用戶：qdxqdxqdxqdx
近距電能傳輸——高效安全近距電能傳輸一般基于電磁感應原理進行。在此技術基礎上，當接收器鄰近發射器時才會進行電能傳輸。電磁感應技術的歷史長達百年，多年米一直應用于各類電子產品中—如此普及全因其簡單、高效以及安全技術概覽以下將為你簡要介紹無線電能傳輸技術。System Overview(Communication)Receiver sends messagesTo provide control information to the transmitterBy load modulation on the power signaTransmitter receives messagesTo receive control information frorn the recelverBy de-modulation of the reflected loadPower Pick Up( Receiver)Secondary coil (L Serial resonance capacitor (C) for efficient power transfer Parallel resonance capacitor(C, )for detection purposes Rectifier: full bridge(diode, or switched)+ capacitor OUTPUT switch for(dis)connecting the loadReceiver modulates load by Switching modulation resistor(R,n),or Switching modulation capacitor(Ca)Transmitter de-modulates reflected load by Sensing pnmary coil curent (p)and/o Sensing primary coil voltage (V,
上傳時間： 2022-03-31
上傳用戶：
為設計高效率、低損耗的PFC電路,本文基于UCC28019進行電路設計。以UCC28019輸出的PWM波形來控制Boost升壓斬波為核心電路,使電路中的電容交替地充放電、電感交替的儲存和釋放能量,最后實現在輸入AC20V~24V電壓情況下穩定輸出DC38V。測試結果表明,系統實現效率為95%左右,電壓調整率小于1%,電源功率因數0.99。交流輸入電壓為19.0-25.8 V時,輸出直流電壓穩定性較好,電感無明顯嘯叫且紋波小,具有一定的帶負載能力和實用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform OUTPUT by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable OUTPUT of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The OUTPUT DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上傳時間： 2022-04-03
上傳用戶：
高通(Qualcomm)藍牙芯片QCC5144_硬件設計詳細指導書（官方內部培訓手冊）其內容是針對硬件設計、部分重要元器件選擇(ESD，Filter）及走線注意事項的詳細說明。2 Power management 2.1 SMPS 2.1.1 Components specification 2.1.2 Input power supply selection 92.1.3 Minimize SMPS EMI emissions 2.1.4 Internal LDOs and digital core decoupling 2.1.5 Powering external components 2.2 Charger 2.2.1 Charger connections.2.2.2 General charger operation2.2.3 Temperature measurement during charging 2.3 SYS_CTRL 3 Bluetooth radio3.1 RF PSU component choice 3.2 RF band-pass filter3.3 Layout (天線 走線的注意事項)4 Audio4.1 Audio bypass capacitors 4.2 Earphone speaker OUTPUT4.3 Line/Mic input 4.4 Headphone OUTPUT optimizition5 LED pads 5.1 LED driver 5.2 Digital/Button input 5.3 Analog input5.4 Disabled 6 Reset pin (Reset#)7 USB interfaces7.1 USB device port7.1.1 USB device port7.1.2 Layout notes 7.1.3 USB charger detectionA QCC5144 VFBGA example schematic and BOM B Recommended SMPS components specificationB.1 Inductor specifition B.2 Recommended inductors B.3 SMPS capacitor specifition
上傳時間： 2022-04-07
上傳用戶：默默
如果在調諧器或電視機附近使用本機或任何其他使用微處理器的電子設備，則可能會產生圖像的噪聲或干擾。如果發生這種情況，請采取以下步驟將本機安裝在盡可能遠離調諧器或T的地方。遠離調諧器或T，遠離本機的電源線和輸入/輸出連接電纜。尤其在使用室內天線或300歐姆饋線。我們建議使用室外天線和75 Q / ohm同軸電纜Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV If this happens, take the following stepsInstall this unit as far away as possible from the tuner or T Run the antenna wires from the tuner or T away from this unit ' s power supply cord and input/OUTPUT connection cables. Noise or disturbance tends to occur particularly when using indoor antennas or300 ohm feeder wires. We recommend using outdoor antennas and 75 Q/ohm coaxial cables
標簽： 功放
上傳時間： 2022-04-22
上傳用戶：
超聲波換能器作為一種實用的檢測手段，能實現聲波所攜帶的信息和電能之間轉換。它的性能優良，價格低廉，操作方便，易于調試，因此在工農業生產中發揮著重要的作用。但目前換能器驅動電路的發射頻率多為40 kHz，本文針對1 MHz的超聲波換能器電路進行了設計，主要介紹了它的發射驅動電路和接收驅動電路的設計方案，并對它們的功能進行了詳細地說明。最后搭建實驗平臺，并對電路的輸入、輸出模塊進行了測試。實驗結果表明，換能器電路運行良好，可以為超聲波高精度測量領域的應用提供參考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an important role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and OUTPUT were tested. Experiments show that the transducer＇ s...
上傳時間： 2022-04-28
上傳用戶：
基于PSIM仿真軟件，分析了Boost電路拓撲結構，設定了參數要求進行電路仿真設計，通過電路仿真軟件PSIM對Boost電路工作在CCM模式下，合理設置占空比參數。實驗結果表明理論分析與仿真的一致性和參數設計的正確性，輸出電壓和電流參數穩定，Boost電路輸出效率高。This design is based on PSIM simulation software,analyzes the topology of Boost circuit,sets the parameter re- quirements for circuit simulation design,and reasonably sets the duty cycle parameters for Boost circuit working in CCM mode through PSIM simulation software.The experimental results show that the theoretical analysis and simulation are consis- tent and the parameter design is correct,the OUTPUT voltage and current parameters are stable.
上傳時間： 2022-05-04
上傳用戶：
The JW? 7805 is a low noise low-dropout (LDO) voltage regulator with enable function that operates from 1.8V to 5.5V. It provides up to 300mA of OUTPUT current and offers low-power operation in miniaturized packaging. JW7805 supports fixed OUTPUT voltage 0.9V, 1.0V, 1.05V, 1.1V,1.2V, 1.3V, 1.35V, 1.5V, 1.8V, 1.85V, 2.1V, 2.2V, 2.3V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V,3.1V, 3.3V, 3.6V, 4.2V, 4.4V and 5.0V. The features of low quiescent current as low as 6uA and almost zero disable current are ideal for powering the battery equipment. JW7805’s low OUTPUT noise and high PSRR are also friendly to RF systems.
標簽： JW7805
上傳時間： 2022-05-06
上傳用戶：slq1234567890
CH7525 is a low-cost, low-power semiconductor device that translates the DisplayPort signal to HDMI/DVI. This innovative DisplayPort receiver with an integrated HDMI Transmitter is specially designed to target the notebook/ultrabook, tablet device and PC market segments. Through the CH7525’s advanced decoding / encoding algorithm, the input DisplayPort high-speed serialized multimedia data can be seamlessly converted to HDMI/DVI OUTPUT.
上傳時間： 2022-06-02
上傳用戶：
ATS2819/ATS2819P標準應用方案主要分為以下功能模塊：Power Supply，BlueTooth，Audio Input/OUTPUT（包括codec、I2C、SPDIF），FM Receiver，disaplay（LED&LCD），USB，SPI NOR Flash Memory，SD/MMC/MS Card等。1.2原理圖設計總體原則1原理圖設計需要按照方案規格的要求實現各項硬件功能，盡量避免功能模塊相互間的資源沖突。如果存在I/O復用，接收復用等情況，除了需注意檢查I/O上電狀態，接口時序等，還需要注意復用的SIO工作頻率與工作電壓域是否符合要求(如WIO)，確保功能設計正確實現。2原理圖設計要求性能達到要求。如穩定性，啟動電壓，功耗，ESD，EMI等。要注意檢查模塊電源開關狀態，選擇的原件標稱及精度、材質，接口保護元件和EMI濾波器等。3系統時鐘26MHZ，要求CL為7~9PF，精度為+-10PPM。這樣才能保證系統能正常工作。4當設計PCB受限于模具大小時，各個模塊無法保證均能得到最優的布局布線(如濾波電容要求靠近IC、走線上要求盡量少的過孔與盡可能短的走線)。因為在此給出一個模塊優先級以供設計人員參考，從而提高方案設計的效率，增加一版work的可行性。將優先級以阿拉伯數據排列
上傳時間： 2022-06-07
上傳用戶：
