The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low OUTPUT ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. LowOUTPUT voltages are easily supported with the 0.6V feedback reference voltage
標簽： pw2053
上傳時間： 2022-02-14
上傳用戶：jason_vip1
PW1555 is a programmable current limit switch with input voltage range selection and OUTPUTvoltage clamping. Extremely low RDS(ON) of the integrated protection N-channel FET helps toreduce power loss during the normal operation. Programmable soft-start time controls the slew rateof the OUTPUT voltage during the start-up time. Independent enable control allows the complicatedsystem sequencing control. It integrates the over-temperature protection shutdown andautorecovery with hystersis
標簽： pw1555
上傳時間： 2022-02-14
上傳用戶：
高清電子書-C++ Primer Plus, 第6版英文版 1438頁Learning C++ is an adventure of discovery, particularly because the language accommodates several programming paradigms, including object-oriented programming, generic programming, and the traditional procedural programming.The fifth edition of this book described the language as set forth in the ISO C++ standards, informally known as C++99 and C++03, or, sometimes as C++99/03. (The 2003 version was largely a technical correction to the 1999 standard and didn’t add any new features.) Since then, C++ continues to evolve.As this book is written, the international C++ Standards Committee has just approved a new version of the standard.This standard had the informal name of C++0x while in development, and now it will be known as C++11. Most contemporary compilers support C++99/03 quite well, and most of the examples in this book comply with that standard. But many features of the new standard already have appeared in some implementations, and this edition of C++ Primer Plus explores these new features. C++ Primer Plus discusses the basic C language and presents C++ features, making this book self-contained. It presents C++ fundamentals and illustrates them with short, to-the-point programs that are easy to copy and experiment with.You learn about input/OUTPUT (I/O), how to make programs perform repetitive tasks and make choices, the many ways to handle data, and how to use functions.You learn about the many features C++ has added to C, including the followi
標簽： C++
上傳時間： 2022-02-19
上傳用戶：trh505
5G通信系統中massive-MIMO-FBMC技術的結合概述摘要為了應對第五代移動通信（5G）中更高數據率和更低時延的需求，大規模MIMO （massive multiple-input multiple-OUTPUT）技術已經被提出并被廣泛研究。大規模 MIMO技術能大幅度地提升多用戶網絡的容量。而在5G中的帶寬研究方面，特別 是針對碎片頻譜和頻譜靈活性問題，現有的正交頻分多址（Orthogonal Frequency Division Multiplexing, OFDM）技術不可能應對未來的挑戰，新的波形方案需要 被設計出來。基于此，FBMC（filter bank multicarrier）技術由于具有比OFDM低 得多的帶外頻譜泄露而被受到重視，并已被標準推進組IMT-2020列為5G物理層 的主要備選方案之一。 本文首先回顧了5G中波形設計方案（主要是FBMC調制）和大規模多天線系 統（即massive MIMO）的現有工作和主要挑戰。然后，簡要介紹了基于Massive MIMO的FBMC系統中的自均衡性質，該性質可以用于減少系統所需的子載波數 目。同時，FBMC中的盲信道跟蹤性質可以用于消除massive MIMO系統中的導頻 污染問題。盡管如此，如何將FBMC技術應用于massive MIMO系統中的誤碼率、 計算復雜度、線性需求等方面仍然不明確，未來更多的研究工作需要在massive MIMO-FBMC方面展開來。 關鍵詞：大規模MIMO；FBMC；自均衡；導頻污染；盲均衡
上傳時間： 2022-02-25
上傳用戶：
Single chip TFT-LCD Controller/Driver with On-chip Frame Memory (FM) Display Resolution: 240*RGB (H) *320(V) Frame Memory Size: 240 x 320 x 18-bit = 1,382,400 bits LCD Driver OUTPUT Circuits- Source OUTPUTs: 240 RGB Channels- Gate OUTPUTs: 320 Channels- Common Electrode OUTPUT Display Colors (Color Mode)- Full Color: 262K, RGB=(666) max., Idle Mode Off- Color Reduce: 8-color, RGB=(111), Idle Mode On Programmable Pixel Color Format (Color Depth) for Various Display Data input Format- 12-bit/pixel: RGB=(444)- 16-bit/pixel: RGB=(565)- 18-bit/pixel: RGB=(666) MCU Interface- Parallel 8080-series MCU Interface (8-bit, 9-bit, 16-bit & 18-bit)- 6/16/18 RGB Interface(VSYNC, HSYNC, DOTCLK, ENABLE, DB[17:0])- Serial Peripheral Interface(SPI Interface)- VSYNC Interface
上傳時間： 2022-03-04
上傳用戶：
ADC模數轉換器件Altium Designer AD原理圖庫元件庫SV text has been written to file : 4.4 - ADC模數轉換器件.csvLibrary Component Count : 29Name Description----------------------------------------------------------------------------------------------------ADC0800 National 8-Bit Analog to Digital ConverterADC0809 ADC0831 ADCADC0832 ADC8 Generic 8-Bit A/D ConverterCLC532 High-Speed 2:1 Analog MultiplexerCS5511 National 16-Bit Analog to Digital ConverterDAC8 Generic 8-Bit D/A ConverterEL1501 Differential line Driver/ReceiverEL2082 Current-Mode MultiplierEL4083 Current Mode Four Quadrant MultiplierEL4089 DC Restored Video AmplifierEL4094 Video Gain Control/FaderEL4095 Video Gain Contol/Fader/MultiplexerICL7106 LMC6953_NSC PCI Local Bus Power SupervisorMAX4147 300MHz, Low-Power, High-OUTPUT-Current, Differential Line DriverMAX4158 350MHz 2-Channel Video Multiplexer-AmplifierMAX4159 350MHz 2-Channel Video Multiplexer-AmplifierMAX4258 250MHz, 2-Channel Video Multiplexer-AmplifierMAX4259 250MHz 2-Channel Video Multiplexer-AmplifierMAX951 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMAX952 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMC1496 Balanced Modulator/DemodulatorPLL100k Generic Phase Locked LoopPLL10k Generic Phase Locked LoopPLL5k Generic Phase Locked LoopPLLx Generic Phase Locked Loop水位計
標簽： adc 模數轉換 altium designer
上傳時間： 2022-03-13
上傳用戶：
電子書-RTL Design Style Guide for Verilog HDL540頁A FF having a fixed input value is generated from the description in the upper portion of Example 2-21. In this case, ’0’ is OUTPUT when the reset signal is asynchronously input, and ’1’ is OUTPUT when the START signal rises. Therefore, the FF data input is fixed at the power supply, since the typical value ’1’ is OUTPUT following the rise of the START signal. When FF input values are fixed, the fixed inputs become untestable and the fault detection rate drops. When implementing a scan design and converting to a scan FF, the scan may not be executed properl not be executed properly, so such descriptions , so such descriptions are not are not recommended. recommended.[1] As in the lower part of Example 2-21, be sure to construct a synchronous type of circuit and ensure that the clock signal is input to the clock pin of the FF. Other than the sample shown in Example 2-21, there are situations where for certain control signals, those that had been switched due to the conditions of an external input will no longer need to be switched, leaving only a FF. If logic exists in a lower level and a fixed value is input from an upper level, the input value of the FF may also end up being fixed as the result of optimization with logic synthesis tools. In a situation like this, while perhaps difficult to completely eliminate, the problem should be avoided as much as possible.
標簽： RTL verilog hdl
上傳時間： 2022-03-21
上傳用戶：canderile
對某四輪獨立驅動電動汽車輪轂電機進行研究,設計一種永磁無刷直流電機控制器.以STM32F103RBT6芯片為基礎,對電機驅動電路、采樣電路和保護電路分別進行硬件設計與分析;同時,采用模塊化軟件設計方案,對該控制器的軟件系統進行升級.實驗驗證表明:所設計的電機控制器能使電機響應迅速、轉速穩定、無超調,且電動車動力輸出性能良好.A permanent magnet brushless direct current motor controller was designed by studying the hub motor of a four-wheel independent drive electric vehicle.Based on STM32 F103RBT6 chip,the hardware design and analysis of motor drive circuit,sampling circuit and protection circuit were carried out respectively.At the same time,modular software design scheme was adopted to upgrade the software system of the controller.Experimental results show that the designed motor controller can ensure the motor fast response,stable speed,no overshoot,and good power OUTPUT performances.
上傳時間： 2022-03-26
上傳用戶：qingfengchizhu
以AT89S52單片機為控制核心,采用電容降壓技術,Buck電路拓撲,PWM驅動模塊和功率器件散熱設計,通過高速的數據采集、主功率輸入輸出模塊和控制模塊,設計一種新型智能車載充電器.在充電過程中,通過負脈沖瞬間放電實現對鉛酸蓄電池的再生修復,提高電池的有效容量,延長使用壽命.該充電器體積小、速度快、效率高、可靠性好.With AT89S52 single chip computer as the control core,a new type of intelligent car-carried charger was designed by using capacitance step-down technology,Buck circuit topology,PWM driving module and power device heat dissipation design,through high-speed data acquisition,main power input and OUTPUT module and control module.In the charging process,the regeneration and repair of lead-acid batteries are realized by instantaneous discharge of negative pulse,which improves the effective capacity of batteries and prolongs their service life.The charger has the advantages of small size,fast speed,high efficiency and good reliability.
標簽： 車載充電器
上傳時間： 2022-03-27
上傳用戶：
在半導體制冷技術的工作性能及其優缺點研究的基礎上,設計了以單片機為核心控制元件,以TEC1-12706為執行元件的半導體制冷溫度控制系統。采用高精度分段式PID控制算法配合PWM輸出控制的方法實現溫度控制;選擇數字傳感器DS18B20為溫度檢測元件,還包含1602液晶顯示模塊、按鍵調整輸入模塊和H橋驅動模塊等。實際測試表明,該系統結構簡單易行,操作方便,工作性能優良,同時針對該系統專門設計的溫控算法,使半導體制冷器能更好地適應不同工況而充分發揮其制冷制熱工作特性。Based on the study of the performance and advantages and disadvantages of thermoelectric cooler(TEC)technology,a thermoelectric cooling temperature control system with single-chip microcomputer as the core control element and TEC1-12706 as the executive element was designed. High precision piecewise PID control algorithm combined with PWM OUTPUT control method is adopted to realize temperature control. The digital sensor DS18B20 is selected as the temperature detection element. It also includes 1602 LCD module,key adjustment input module and H bridge drive module. The actual test shows that the system has simple structure,convenient operation and excellent performance. Meanwhile,the temperature control algorithm specially designed for the system can make the semiconductor cooler better adapt to different working conditions and give full play to its refrigeration and heating characteristics.
上傳時間： 2022-03-27
上傳用戶：
