Luminary Micro provides an analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and Overall system performance.
This application note describes how the existing dual-port block memories in the Spartan™-IIand Virtex™ families can be used as Quad-Port memories. This essentially involves a dataaccess time (halved) versus functionality (doubled) trade-off. The Overall bandwidth of the blockmemory in terms of bits per second will remain the same.
多遠程二極管溫度傳感器-Design Considerations for pc thermal management
Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The Overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
The Maxim Integrated 71M6541-DB REV 3.0 Demo Board is a demonstration board for evaluating the 71M6541 device for single-phase electronic energy metering applications in conjunction with the Remote Sensor Inter-face. It incorporates a 71M6541 integrated circuit, a 71M6601 Remote Interface IC, peripheral circuitry such as a serial EEPROM, emulator port, and on-board power supply. A serial to USB converter allows communication to a PC through a USB port. The Demo Board allows the evaluation of the 71M6541 energy meter chip for measurement accuracy and Overall system use.
Abstract: With industrial/scientific/medical (ISM) band radio frequency (RF) products, often times users are new to the structure of Maxim's low pin-count transmitters andfully integrated superheterodyne receivers. This tutorial provides simple steps that can be taken to get the best performance out of these transmitters and receivers whileproviding techniques to measure the Overall capability of the design.
Abstract: Using a wafer-level package (WLP) can reduce the Overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
This application note describes how the existing dual-port block memories in the Spartan™-IIand Virtex™ families can be used as Quad-Port memories. This essentially involves a dataaccess time (halved) versus functionality (doubled) trade-off. The Overall bandwidth of the blockmemory in terms of bits per second will remain the same.
VHDL 關于2DFFT設計程序
u scinode1 ∼ scinode9.vhd: Every SCI node RTL vhdl code. The details can be
seen in the following section.
u 2dfft.vhd: The top module includes these scinodes and form a 3x3 SCI Torus
network, and it support these sub-modules scinode1∼ scinode9 reset and clk
and global_cnt signals to synchronous the sub-modules to simplify the Overall
design.
u proj2.wfc: VSS simulation result that is the same as the ModelSim simulation
result.
u Pro2_2.wfc: VSS simulation result of another test pattern can’t cause overflow
situation.
Often it is necessary to add some logical control to a MATLAB algorithm to allow the generated hardware to function correctly in the Overall system. This lab exercise will explore how hardware control can be added to a MATLAB algorithm and synthesized using AccelDSP Synthesis.
This Document provides the High Level Design specification for the Bootloader development and library porting for ADSP-BF533 based EZ-Kit Lite Board and STAMP Board. This document is meant to be the one of the inputs for the System Test Plan and the Overall implementation of the same. This document also details the approach and assumptions made for the design
