The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 Providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A Providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
The TJA1042 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, Providing the differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
The TJA1051 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, Providing differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
The ISO7220 and ISO7221 are dual-channel digital isolators. To facilitate PCB layout, the channels are orientedin the same direction in the ISO7220 and in opposite directions in the ISO7221. These devices have a logic inputand output buffer separated by TI’s silicon-dioxide (SiO2) isolation barrier, Providing galvanic isolation of up to4000 V. Used in conjunction with isolated power supplies, these devices block high voltage, isolate grounds, andprevent noise currents on a data bus or other circuits from entering the local ground and interfering with ordamaging sensitive circuitry.
Abstract: Many industrial/scientific/medical (ISM) band radio frequency (RF) receivers use an external Sallen-Key datafilter and a data slicer to generate the baseband digital output. This tutorial describes the ISM-RF Baseband Calculator,which can be used to calculate the filter capacitor values and the data slicer RC components, while Providing a visualexample of the baseband signals.
多遠程二極管溫度傳感器-Design Considerations for pc thermal management
Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by Providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
A language monitor provides a full duplex communications path between the print spooler and bi-directional printers that are capable of Providing software-accessible status information and adds printer control information, such as commands defined by a printer job language, to the data stream s.
ZipForge is a fast ZIP compression library. With this toolkit you can easily add archive functionality to your projects. ZipForge includes our new unique techonology, a transaction system. This innovative solution gives you a fast and easy way of updating archive files Providing data integrity like a reliable database system. ZipForge Personal is free for personal use. Any company that uses ZipForge in its projects must order ZipForge Pro.
SDP Search and Record generator
OVERVIEW:
Recognizing the difficulty in creating an SDP service description and search
from scratch, Microsoft is Providing a sample utility in bthnscreate.cxx to
automatically create a service or record. This utility can be run to create
an SDP record or to setup an SDP Service, Attribute, or ServiceAttribute
search based on information stored in a human readable file.
