Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ”playground”prototyping area. The prototyping area has padsfor Dip-8, S8, MS8, or S6 packages with breadboarding connections to each pin and two convenientpower buses and ground bus surrounding theentire area. This area is for conditioning signals tocontrol the timer function and for adding loads controlled in time.
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。
Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
為了有效地提升鉛酸蓄電池的使用壽命，同時實現對充電過程的監控，設計出一種用單片機控制的36 V鉛酸蓄電池充電電源。本電路采用反激式拓撲，連續電流工作模式，電源管理IC設計在電源的副邊，由ELAN公司的EM78P258N單片機模擬，是用可編程器件模擬電源管理IC，實現智能電源低成本化的一次成功嘗試，通過對單片機的軟件設計實現了充電電源的狀態顯示、充電時間控制、報警、過溫保護、過壓保護、過流保護等功能。本充電器真正的實現了鉛酸蓄電池的三段式充電過程，其最高輸出功率可達90 W，效率約85%，成本不到20元，具有很高的市場競爭力。
Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
單片機作為一種微型計算機，其內部具有一定的存儲單元（8031除外），但由于其內部存儲單元及端口有限，很多情況下難以滿足實際需求。為此介紹一種新的擴展方法，將數據線與地址線合并使用，通過軟件控制的方法實現數據線與地址線功能的分時轉換，數據線不僅用于傳送數據信號，還可作為地址線、控制線，用于傳送地址信號和控制信號，從而實現單片機與存儲器件的有效連接。以單片機片外256KB數據存儲空間的擴展為例，通過該擴展方法，僅用10個I/O端口便可實現，與傳統的擴展方法相比，可節約8個I/O端口。
Abstract:
As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
飛機電網故障時，機載電氣盒必須在延遲時間內切斷電網，保護機載設備。采用AT89S52設計的電氣盒測試儀能夠測試電氣盒保護功能，測量延遲時間。實際應用結果表明，該測試儀具有測量準確、可靠性高、成本低等優點。
Abstract:
The helicopter-electrical-box must shut off the helicopter power，protect the equipments of the helicopter when the helicopter power is failed.The tester for the helicopter-electrical-box based on AT89S52is used for testing the protect-ing function and measuring the delay time.Application results show this tester has some advantages,such as accurate mea-surement,high dependability,economical cost etc.
介紹了采用ATmega48單片機實現三相無刷直流電機控制器的方法。利用Atmega48獲得帶死區的脈寬調制（PWM）、霍爾傳感器的換相處理、正弦驅動信號的產生和電機轉速的控制等功能。采用該方法的優點是所需的外圍器件少，成本低。
Abstract:
The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
氣壓是氣象監測中的一個重要參數，提出了一種氣壓數據采集模塊設計方案，該模塊采用數字氣壓傳感器MS5534B、MSP430單片機MSP430F2272和帶實時時鐘（RTC）64 KB鐵電存儲器。通過低功耗軟件設計方法以微安級整體平均功耗實現了氣壓數據的采集和存儲，適合電池供電的連續高精度氣壓采集應用。給出了模塊的軟硬件設計以及MS5534B的性能指標和使用經驗。
Abstract:
Air pressure is an important parameter in weather monitor.This paper futs forward a new design scheme of low power-air pressure data acquisition module.The module uses a digital output barometer sensor MS5534B,MSP430 microcontroller MSP430F2272 and integrated RTC 64KB FRAM,precision air pressure measurement and storage chip.Another point of this module is low power consumption, so it is well suited for battery powered air pressure data acquisition applications. At the same time,the software and hardware deign of module is presented,And the speciaties and use notices of MS5534B are given.
采用單片機AT89C2051實現溫度測量與控制,鍵盤和顯示電路實現溫度的設定、修改、清零以及當前溫度值的顯示,并對溫度超過上下限進行報警。闡述了該系統設計的硬件和軟件設計。
Abstract:
The system of temperature measuring and controling is realized based on AT89C2051.The keyboard and display circuit is designed,which can be used for setting and modifying temperature value,resetting and displaying the present temperature value.At the same time the warning circuit is also designed in the system,which can deal with the alarm when temperature exceeds the upper limit and the lower limit.The hardware and software design of the system are explained．
