Boost LED drivers are often used to drive LEDs in series. If an LED fails while open,overvoltage protection (OVP) is necessary to avoid the damage to a boost integrated circuit (IC) or output capacitor. This application Report presents the solutions to increase the TPS61043 LED driver OVP threshold.
Abstract: The rapid build out of today's smart grid raises a number of security questions. In this article,we review two recent well-documented security breaches and a Report of a security gap. These situationsinclude a 2009 smart-meter hack in Puerto Rico; a 2012 password discovery in grid distributionequipment; and insecure storage of a private key in distribution automation equipment. For each of theseattacks, we examine the breach, the potential threat, and secure silicon methods that, as part of acomplete security strategy, can help thwart the attacks.
Digitemp Junior – An RS-232 Port-Powered Digital Thermometer
Digitemp Jr. is a device that is designed to measure
and Report ambient temperature. When connected to
an RS-232 port on any PC, it will periodically measure
and Report in ASCII form the ambient temperature in
degrees Celsius. These temperature readings can be
monitored with any terminal program. If the terminal
program supports capture to disk, the temperature
readings can be saved to disk for further analysis with
a spreadsheet program or other data analysis tool. The
simple ASCII output format of Digitemp Jr. makes it rel-
atively easy to write custom software for receiving,
recording, and analyzing ambient temperature data.
Best of all, Digitemp Jr. requires no external power sup-
plies or batteries. It is powered directly by the RS-232 port.
Digitemp Jr. is a device that is designed to measure
and Report ambient temperature. When connected to
an RS-232 port on any PC, it will periodically measure
and Report in ASCII form the ambient temperature in
degrees Celsius. These temperature readings can be
monitored with any terminal program. If the terminal
program supports capture to disk, the temperature
readings can be saved to disk for further analysis with
a spreadsheet program or other data analysis tool. The
simple ASCII output format of Digitemp Jr. makes it relatively
easy to write custom software for receiving,
recording, and analyzing ambient temperature data.
Best of all, Digitemp Jr. requires no external power supplies
or batteries. It is powered directly by the RS-232
port.
This application Report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
<Almost since the introduction of microcontrollers as electronic components there always has been an oscillatorcircuit on the device to make it work. From application point of view only some external components wererequired to make it work. However, to make sure that it will always work required more effort. This Report is basedon feedback from the market from customers applying 8-bit mircrocontrollers.>
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This Report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip Microcontrollers. The XA-S3 combines many powerful peripherals on one chip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-chip peripherals is the I2C bus interface. This Report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
