Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking Requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
標簽： agilent
上傳時間： 2022-02-20
上傳用戶：
基于FPGA設計的相關論文資料大全 84篇用FPGA實現FFT的研究 劉朝暉 韓月秋 摘 要 目的 針對高速數字信號處理的要求，給出了用現場可編程門陣列(FPGA)實現的 快速傅里葉變換(FFT)方案.方法 算法為按時間抽取的基4算法，采用遞歸結構的塊浮點運 算方案，蝶算過程只擴展兩個符號位以適應雷達信號處理的特點，乘法器由陣列乘法器實 現.結果 采用流水方式保證系統的速度，使取數據、計算旋轉因子、復乘、DFT等操作協 調一致，在計算、通信和存儲間取得平衡，避免了瓶頸的出現.結論 實驗表明，用FPGA 實現高速數字信號處理的算法是一個可行的方案. 關鍵詞 離散傅里葉變換； 快速傅里葉變換； 塊浮點運算； 可編程門陣列 分類號 TP39； TN957.511 Implementation of FFT with FPGA Technology Liu Zhaohui Han Yueqiu (Department of Electronics Engineering, Beijing Institute of Technology, Beijing 100081) Abstract Aim To propose a scheme for implementing FFT with FPGA in accor-dance with the Requirement for high speed digital signal processing. Methods The structure of FPGA and Requirement of system were considered in the experiment, radix-4 algorithm of DIT and recursive structure were adopted. The group float point arithmetic operation was used in the butterfly and the array multiplier was used to realize multiplication. Results The pipeline pattern was used to ensure the system speed, it made fetching data, calculating twiddle factor, complex multiplication and D
標簽： fpga
上傳時間： 2022-03-23
上傳用戶：
本系統采用電動機電樞供電回路串接采樣電阻的方式來實現對小型直流有刷電動機的轉速測量。該系統主要由二階低通濾波電路,小信號放大電路、單片機測量顯示電路、開關穩壓電源電路等組成。同時自制電機測速裝置,用高頻磁環作為載體,用線圈繞制磁環,利用電磁感應原理檢測電機運行時的漏磁,將變化的磁場信號轉化為磁環上的感應電流。用信號處理單元電路將微弱電信號轉化為脈沖信號,送由單片機檢測,從而達到準確測量電機的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the Requirement of accurate measurement of motor speed.
標簽： 直流電動機
上傳時間： 2022-03-26
上傳用戶：
近年來反季節種植已成火熱趨勢,溫室大棚的普及十分迅速,而溫室大棚對自動化、智能化的要求也越來越迫切,本系統將溫室大棚的溫濕度、二氧化碳濃度各個方面的檢測,通風、澆灌、溫度、噴灑農藥等各個方面的控制進行綜合系統研究,實現溫室大棚對自動化、智能化的要求。這一系統是基于單片機控制的智能檢測,控制系統包含單片機主控模塊、感應檢測模塊、傳感模塊,顯示、控制模塊等[1]。從而提高溫室大棚的種植效率,減少勞動力,提高利潤等。In recent years,counter-season planting has become a hot trend featuring the rapid popularization of greenhouse and urgent Requirement for the automation and intellectualization of greenhouse.This paper offers a comprehensive and systematic study of the monitoring of temperature,humidity and carbon dioxide concentration in the greenhouse and the control of ventilation,irrigation,temperature and pesticide spraying in order to achieve automation and intellectualization in greenhouse.This system is based on the intelligent detection controlled by single chip computer with the control system including the main control module,induction detection module,sensing module,display and control module of single chip computer,which is effective in improving planting efficiency of greenhouse,reducing labor force and increasing profits.
上傳時間： 2022-03-27
上傳用戶：
電學中的測量技術涉及范圍非常廣,電流測量在電學計量中占有非常重要的位置。如何精確地進行電流測量是精密測量的一大難題。傳統的電流檢測電路多采用運算放大芯片與片外電流檢測電路相結合的方式,電路集成度很低,需要較多的接口和資源才能完成對電路的檢測。本文把所有電路部分都集成在一塊芯片上,包括檢測電阻,運算放大器電路及模擬轉數字轉換電路,從而在電路內部可以進行電流檢測,使電路更好的集成化。前置電路使用二級共源共柵結構的運算放大器,減小溝道長度調制效應造成的電流誤差。10位SAR ADC中采用電容驅動能力強的傳輸門保證了模數轉化器的有效精度。比較器模塊采用再生鎖存器與遲滯比較器作為基礎單元組合解決精密測量的問題。本設計可以作為嵌入芯片內的一小部分而檢測芯片中的微小電流1mA~100mA,工作電壓在1.8v左右,電流檢測精度預期達到10uA的需求。The measurement technology in electricity involves a wide range,and current measurement plays a very important position in electrical measurement.How to accurately measure current is a big problem in precision measurement. The traditional current detecting circuit adopts the combination of the operational amplifier chip and theoff-chip current detecting circuit, The circuit integration is very low, and more interfaces and resources are needed tocomplete the circuit detection.This topic integrates all the circuit parts into one chip, including detection resistance, operational amplifier circuit andanalog to digital conversion circuit. Highly integrated circuit makes the external resources on the chip more intensive,so that current detection can be carried out inside the circuit, so that the circuit can be better integrated. Thefront-end circuit of this project uses two-stage cascade operational amplifier and cascade tube to reduce the currenterror caused by channel length modulation effect. In 10-bit SAR ADC, the transmission gate with strong capacitivedriving ability ensures the effective accuracy of the analog-to-digital converter. Comparator module uses regenerativelatch and hysteresis comparator as basic unit to solve the difficult problem of precision measurement. This topic can beused as a small part of the embedded chip to detect the micro-current in the chip 1 mA~100 mA, the working voltageis about 1.8v, and the current detection accuracy is expected to reach the Requirement of 10 uA.
上傳時間： 2022-04-03
上傳用戶：
目的:自主研制一款超聲手術刀電源控制系統,以減少能量的消耗,維持手術刀的正常溫度。方法:對超聲換能器在諧振附近的等效電路建立模型,并設計基于數字信號處理(DSP)的超聲手術刀的硬件控制系統。結果:經對電源控制系統的電路和工作性能測試,生成的電流和電壓的有效值等參數,能夠及時調整電源的頻率,并達到預期的功能指標,使超聲手術刀工作在諧振狀態。結論:以DSP為核心設計的超聲手術刀電源控制系統,測試指標均能夠達到預期的要求,能夠使系統在諧振狀態下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal processing(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative Requirement, and can take this system to work in syntonic situation.
上傳時間： 2022-04-03
上傳用戶：bluedrops
為適應雙向DC/DC功率變換的電流采樣需求,一種高精度高邊電流采樣電路被提出。其基本思想是在功率電路的高邊串入采樣電阻,借助電流鏡原理并引入偏置電流電路,將雙向電流均轉換為正向電壓輸出。通過理論分析與仿真結合的方法對電流鏡采樣原理及4種不同的偏置電流電路方案進行對比,最后通過實驗數據驗證了高精度高邊電流采樣電路的有效性。實驗數據表明,該采樣電路可在-25~75℃的溫度工作范圍內,針對-10~＋10 A范圍內的電流采樣實現優于5%的采樣精度。Current sensing plays an important role in controlling,monitoring or protection functions of power systems.To meet the current sensing Requirement of bidirectional DC/DC converters,a high-accuracy bidirectional current sensing circuit is proposed.The proposed current sensing circuit inserts a resistor in the path of the current to be sensed,while the current mirror and biased current circuit are introduced.Therefore,the bidirectional current can be expressed by positive voltage.By theoretical analysis and simulation,the sampling theory is analyzed and four biased current circuits are compared.At last,experimental results verified the proposed method.It is demonstrated that the proposed current sensing circuit can achi...
上傳時間： 2022-04-22
上傳用戶：
