本程序的要求是已知幾個節點x及節點函數f（x），要求近似函數！只要輸出每點函數，對角線上的值，和最后一行的值，為繼續插值準備！ 例如：0.00 0.00000 0.20 0.20134 0.30 0.30452 0.50 0.52110 得到結果：0.00000 0.20134 1.006700 0.30452 0.083666 0.52110 1.082900 0.170333 0.173334 f(0.230000)=0.249337 Rx(0.230000)=-1.46917e-09f
上傳時間： 2013-12-30
上傳用戶：王慶才
The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both Rx and Tx Interrupt Service Routines.
標簽： ESAcademy following directory examples
上傳時間： 2015-04-25
上傳用戶：hasan2015
The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both Rx and Tx Interrupt Service Routines.
標簽： ESAcademy following directory examples
上傳時間： 2013-12-13
上傳用戶：牛津鞋
The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both Rx and Tx Interrupt Service Routines.
標簽： ESAcademy following directory examples
上傳時間： 2014-01-06
上傳用戶：zukfu
A system simulation environment in Matlab/Simulink of RFID is constructed in this paper. Special attention is emphasized on the analog/RF circuit.Negative effects are concerned in the system model,such as phase noise of the local oscillator,TX-RX coupling,reflection of the environment, AWGN noise,DC offset,I/Q mismatch,etc.Performance of the whole system can be evaluated by changing the coding method,parameters of building blocks,and operation distance.Finally,some simulation results are presented in this paper.
標簽： environment constructed simulation Simulink
上傳時間： 2014-01-09
上傳用戶：zhangliming420
smsc911x 網卡驅動 This the users/programmers guide for the LAN911x Linux Driver The following sections can be found below * Revision History * Files * Features * Driver Parameters * Rx Performance Tuning * Tested Platforms * Rx Code Path * Tx Code Path * Platform Interface Descriptions
標簽： 911x programmers 911 following
上傳時間： 2014-12-02
上傳用戶：sssl
基于OFDM的無線寬帶系統仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation. System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
標簽： simulator i.e. system-level link-level
上傳時間： 2016-03-15
上傳用戶：xsnjzljj
在c++builder環境下一個串口通信程序，包括界面的設計和串口通信函數的設計，實現了串口通信。在文件夾TX-RX中。
上傳時間： 2013-12-10
上傳用戶：ippler8
NRF905驅動代碼 // The content of this struct is nRF905 s initialize data. // CH_NO=1 433MHZ Normal Opration,No Retrans RX,TX Address is 4 Bytes // RX TX Payload Width is 32 Bytes Disable Extern Clock Fosc=16MHZ // 8 Bits CRC And enable
標簽： initialize 905 content Normal
上傳時間： 2013-12-16
上傳用戶：lanjisu111
一個UWB仿真程序包，里面包含信號生成，信道模擬，Tx/Rx等模塊。M-file
上傳時間： 2016-05-22
上傳用戶：xiaoxiang
<button id="guksi"></button>