MATLAB Code for Optimal Quincunx Filter
Bank Design
Yi Chen
July 17, 2006
This file introduces the MATLAB code that implements the two algorithms (i.e., Algorithms
1 and 2 in [1], or Algorithms 4.1 and 4.2 in [2]) used for the construction of
quincunx filter banks with perfect reconstruction, linear phase, high coding gain, certain
vanishing moments properties, and good frequency selectivity. The code can be
used to design quincunx filter banks with two, three, or four lifting steps. The SeDuMi
Matlab toolbox [3] is used to solve the SECOND-Order cone programming subproblems
in the two algorithms, and must be installed in order for this code to work.
Matlab script for solution to the driven cavity problem on a staggered grid using a divergence formulation and SECOND-Order Runge-Kutta time integration.
This software is developed to provide ease with controller design. For PID control, options are given
to design and analyse the compensated and uncompensated system. You are free to choice among Proportional
PI, PD and PID mode of control. Both frequency and time domain characteristics can be observed. Special
Menus are given to observe time and frequency response plots. For Statefeedback controller similar options
are given. But this is limited to second order system only.
本系統采用電動機電樞供電回路串接采樣電阻的方式來實現對小型直流有刷電動機的轉速測量。該系統主要由二階低通濾波電路,小信號放大電路、單片機測量顯示電路、開關穩壓電源電路等組成。同時自制電機測速裝置,用高頻磁環作為載體,用線圈繞制磁環,利用電磁感應原理檢測電機運行時的漏磁,將變化的磁場信號轉化為磁環上的感應電流。用信號處理單元電路將微弱電信號轉化為脈沖信號,送由單片機檢測,從而達到準確測量電機的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of SECOND-Order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
This project developed in java leads us to realize a flight reservation system in order to emulate databases containing the structures for the flight and for the booking. These bases extend the List interface and implements additional search鈥檚 methods.
Two interfaces provide an access to this system. The first one reads and handles reservation request message from a terminal. The arguments are then processed throw a middleware interface that call the flight system methods. The second one, a Graphical User Interfaces (GUI) application using Swing Java Foundation Classes (JFC), offers a simpler access to the systems.