The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上傳時間： 2013-11-13
上傳用戶：fredguo
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上傳時間： 2013-10-13
上傳用戶：bakdesec
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上傳時間： 2014-01-18
上傳用戶：bs2005
The TRS232E is a dual driver/receiver that includes a capacitive voltage generator to supply TIA/RS-232-Fvoltage levels from a single 5-V supply. Each receiver converts TIA/RS-232-F inputs to 5-V TTL/CMOS levels.This receiver has a typical threshold of 1.3 V, a typical hysteresis of 0.5 V, and can accept ±30-V inputs. Eachdriver converts TTL/CMOS input levels into TIA/RS-232-F levels. The driver, receiver, and voltage-generatorfunctions are available as cells in the Texas Instruments LinASIC™ library.
上傳時間： 2013-10-07
上傳用戶：waitingfy
The main oscillator allows either a crystal or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillator circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillator to clock the device after theboot process has completed.
標簽： Stellaris Clocking Options for
上傳時間： 2013-10-14
上傳用戶：pol123
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
標簽： MULTICHANNEL 5.5 TO RS
上傳時間： 2013-10-19
上傳用戶：ddddddd
The ISO7220 and ISO7221 are dual-channel digital isolators. To facilitate PCB layout, the channels are orientedin the same direction in the ISO7220 and in opposite directions in the ISO7221. These devices have a logic inputand output buffer separated by TI’s silicon-dioxide (SiO2) isolation barrier, providing galvanic isolation of up to4000 V. Used in conjunction with isolated power supplies, these devices block high voltage, isolate grounds, andprevent noise currents on a data bus or other circuits from entering the local ground and interfering with ordamaging sensitive circuitry.
上傳時間： 2013-10-24
上傳用戶：hbsunhui
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上傳時間： 2013-10-11
上傳用戶：dianxin61
The P82B96 offers many different ways in which it can be used as abus interface. In its simplest application it can be used as aninterface between bus systems operating from different supplyvoltages. Opto isolation between two bus systems is possible, andalso the availability of the Tx and Rx signals permits interfacing ofthe P82B96 with other bus systems which separate the forwardoutput path, from the backward input signal path.
上傳時間： 2013-10-11
上傳用戶：洛木卓
The CAT9555 is a CMOS device that provides 16-bitparallel input/output port expansion for I²C and SMBuscompatible applications. These I/O expanders providea simple solution in applications where additional I/Osare needed: sensors, power switches, LEDs,pushbuttons, and fans.
上傳時間： 2014-01-09
上傳用戶：1101055045
<tfoot id="gljqa"></tfoot>
<strike id="gljqa"></strike>
