This program accesses a SPI EEPROM using polled mode access. The F12x MCU is configured in 4-wire Single Master Mode, and the EEPROM is the only slave device connected to the SPI bus. The read/write operations are tailored to access a Microchip 4 kB EEPROM
標簽： configured accesses program EEPROM
上傳時間： 2016-03-29
上傳用戶：gut1234567
// This program accesses a SPI EEPROM using polled mode access. The F06x MCU // is configured in 4-wire Single Master Mode, and the EEPROM is the only // slave device connected to the SPI bus. The read/write operations are // tailored to access a Microchip 4 kB EEPROM 25LC320. The relevant hardware // connections of the F06x MCU are shown here:
標簽： configured accesses program EEPROM
上傳時間： 2014-01-18
上傳用戶：liglechongchong
// This program accesses a SPI EEPROM using polled mode access. The F06x MCU // is configured in 4-wire Single Master Mode, and the EEPROM is the only // slave device connected to the SPI bus. The read/write operations are // tailored to access a Microchip 4 kB EEPROM 25LC320. The relevant hardware // connections of the F06x MCU are shown here:
標簽： configured accesses program EEPROM
上傳時間： 2016-04-12
上傳用戶：qb1993225
練習并掌握多任務實時操作系統下Task 調度、Task 間主要通信手段（信號量、消息隊列等）、RISC 處理器 I/O 端口控制等內容，并形成嵌入式實時應用軟件的良好編程習慣。創建多Task，為每個Task 創建私有的Message Queue，每個Task 只通過自己的私有Message Queue 接收消息；Task 間消息通信通過向對方私有MessageQueue 發送消息完成。 Task1：管理Task。負責系統啟動時同步系統中其他Task 的啟動同步，利用信號量的semFlush()完成。同時接收各Task 的告警信息，告警信息需編號以logmsg 方式輸出。本task 負責系統結束時的Task 刪除處理。 Task2：console 命令行接收Task。接收并分析console 發來的命令行及參數。自行設置5 種以上命令，并根據命令的內容向Task3 或/及Task4 發送激勵消息。同時實現系統退出命令，使系統采用適當方式安全退出。收到非法命令向Task1告警。 Task3：Led 控制Task。接收Led 控制消息（命令），自定義Led 顯示方式表現命令執行情況。本task 應負責led 相關I/O port 初始化。收到非法led 控制命令向Task1 告警。 Task4：console 輸出Task。接收需打印輸出的字串消息（命令），輸出到console。收到長度為0 或超常字串向Task1 告警。
上傳時間： 2016-04-12
上傳用戶：iswlkje
C8051程序， writes text to the serial port of the 8052，用keil編譯
上傳時間： 2016-04-15
上傳用戶：牛布牛
This manual describes Freescale’s IEEE™ 802.15.4 Standard compliant MAC/PHY software. The Freescale 802.15.4 MAC/PHY software is designed for use with the Freescale MC1319x and MC1320x, family of short range, low power, 2.4 GHz Industrial, Scientific, and Medical (ISM) band transceivers, designed for use with the HCS08 Family of MCUs. The MAC/PHY software also works with the MC1321x family of short range, low power, 2.4 GHz ISM band transceivers that incorporate a low power 2.4 GHz radio frequency transceiver and an 8-bit microcontroller into a single LGA package. Throughout this manual, the term transceiver refers to either the MC1319x, MC1320x, or the internal counterpart inside the MC1321x System in a Package (SiP).
標簽： Freescale describes compliant Standard
上傳時間： 2016-04-17
上傳用戶：caiiicc
This little Program allows you to send commands to the CardReader (CT-BCS) or to the Card itself. First you will be ask to what Port the Reader is connected (0=COM1, 1=COM2). Then the Class-Byte (CLA), Instruction-Byte (INS), Parameter 1 (P1), Parameter 2 (P2). If wou don愒 want to send Parameter 3 (P3) press Ctrl-d (^d). If you enter a number then you have to the Bytes of the Datafield. After the last Byte of the Datafield is entered the whole APDU is send the replay is displayed. After that you can send the next APDU.
標簽： CardReader the commands to
上傳時間： 2016-04-23
上傳用戶：nanxia
This will sample all 8 A/D-channels by the continous mode. Each end of conversion will call an interrupt routine, where the AD-channel is put to Port4[2..0] and the upper nibble of the result is put to Port4[7..4]. Port 4 is connected to the user LEDs of the FlashCan100P Evaluation-Board
標簽： will D-channels conversion continous
上傳時間： 2013-12-09
上傳用戶：zm7516678
富士通單片機MB902420系列 CAN Project: CAN0 will work as a simple Repeater. Received data will appear at Port P47..P40 (UserLEDs of FlashCan100P) and will send out again as byte-packages to ID#2 Receive-Buffer #1 : basic can Transmit-Buffer #6 : full-can ID #2
標簽： will Repeater Received Project
上傳時間： 2016-04-27
上傳用戶：www240697738
The neuro-fuzzy software for identification and data analysis has been implemented in the MATLAB language ver. 4.2. The software trains a fuzzy architecture, inspired to Takagi-Sugeno approach, on the basis of a training set of N (single) output-(multi) input samples. The returned model has the form 1) if input1 is A11 and input 2 is A12 then output =f1(input1,input2) 2) if input1 is A21 and input 2 is A22 then output =f2(input1,input2) 看不懂，據高手說，非常有用。
標簽： identification neuro-fuzzy implemented analysis
上傳時間： 2014-01-12
上傳用戶：zgu489
