In an increasing trend, telecommunications, networking,audio and instrumentation require low noise power supplies.In particular, there is interest in low noise, lowdropout linear regulators (LDO). These components powernoise-sensitive circuitry, circuitry that contains noisesensitiveelements or both. Additionally, to conserve power,particularly in battery driven apparatus such as cellulartelephones, the regulators must operate with low input-tooutputvoltages.1 Devices presently becoming availablemeet these requirements (See separate section, “A Familyof 20mVRMS Noise, Low Dropout Regulators”).
上傳時間： 2013-10-30
上傳用戶：yeling1919
For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (See Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上傳時間： 2013-10-19
上傳用戶：royzhangsz
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for batteryoperation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation mustfunction at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽： Circuitry Operation Single Cell
上傳時間： 2013-10-30
上傳用戶：hz07104032
In predominantly digital systems it is often necessaryto include linear circuit functions. Traditionally, separatepower supplies have been used to run the linear components(See Box, “Linear Power Supplies—Past, Present,and Future”).
標簽： Designing Operation Circuits Linear
上傳時間： 2013-11-04
上傳用戶：sdq_123
為解決傳統可視倒車雷達視頻字符疊加器結構復雜，可靠性差，成本高昂等問題，在可視倒車雷達設計中采用視頻字符發生器芯片MAX7456。該芯片集成了所有用于產生用戶定義OSD，并將其插入視頻信號中所需的全部功能，僅需少量的外圍阻容元件即可正常工作。給出了以MAX7456為核心的可視倒車雷達的軟、硬件實現方案及設計實例。該方案具有電路結構簡單、價格低廉、符合人體視覺習慣的特點。經實際裝車測試，按該方案設計的可視倒車雷達視場清晰、提示字符醒目、工作可靠，可有效降低駕駛員倒車時的工作強度、減少倒車事故的發生。 Abstract: A new video and text generation chip，MAX7456，was used in the design of video parking sensor in order to simplify system structure，improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure，lower cost，and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and reliable performance，which makes the driver easy to See backward and reduces chance of accidents.
上傳時間： 2013-12-10
上傳用戶：qiaoyue
AVR Studio 4.12 includes new device support and numerous overall enhancements;new breakpoint system, integrated AVR GCC development and improved docking system!See release notes for more details.
上傳時間： 2013-12-29
上傳用戶：450976175
This article has been contributed to the TI Developer Wiki. To See the most recently updated version or tocontribute, visit this topic at:
上傳時間： 2013-11-04
上傳用戶：釣鰲牧馬
This document describes part number speciÞc changes to recommended operating conditions and revised electrical speciÞcations,as applicable, from those described in the generalMPC7400 Hardware SpeciÞcations.SpeciÞcations provided in this Part Number SpeciÞcation supersede those in theMPC7400 Hardware SpeciÞcationsdated 9/99(order #: MPC7400EC/D) for these part numbers only; speciÞcations not addressed herein are unchanged. This document isfrequently updated, refer to the website at http://www.mot.com/SPS/PowerPC/ for the latest version.Note that headings and table numbers in this data sheet are not consecutively numbered. They are intended to correspond to theheading or table affected in the general hardware speciÞcation.Part numbers addressed in this document are listed in Table A. For more detailed ordering information See Table B.
上傳時間： 2013-11-19
上傳用戶：qiaoyue
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (See Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上傳時間： 2013-10-21
上傳用戶：xiaozhiqban
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (See Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (See Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (SeeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (See Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上傳時間： 2013-10-22
上傳用戶：taiyang250072
