以AT89S52單片機為控制核心,采用電容降壓技術,Buck電路拓撲,PWM驅動模塊和功率器件散熱設計,通過高速的數據采集、主功率輸入輸出模塊和控制模塊,設計一種新型智能車載充電器.在充電過程中,通過負脈沖瞬間放電實現對鉛酸蓄電池的再生修復,提高電池的有效容量,延長使用壽命.該充電器體積小、速度快、效率高、可靠性好.With AT89S52 single chip computer as the control core,a new type of intelligent car-carried charger was designed by using capacitance step-down technology,Buck circuit topology,PWM driving module and power device heat dissipation design,through high-speed data acquisition,main power input and output module and control module.In the charging process,the regeneration and repair of lead-acid batteries are realized by instantaneous discharge of negative pulse,which improves the effective capacity of batteries and prolongs their service life.The charger has the advantages of small size,fast speed,high efficiency and good reliability.
標簽： 車載充電器
上傳時間： 2022-03-27
上傳用戶：
數字示波器功能強大,使用方便,但是價格相對昂貴。本文以Ti的MSP430F5529為主控器,以Altera公司的EP2C5T144C8 FPGA器件為邏輯控制部件設計數字示波器。模擬信號經程控放大、整形電路后形成方波信號送至FPGA測頻,根據頻率值選擇采用片上及片外高速AD分段采樣。FPGA控制片外AD采樣并將數據輸入到FIFO模塊中緩存,由單片機進行頻譜分析。測試表明:簡易示波器可以實現自動選檔、多采樣率采樣、高精度測頻及頻譜分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-processing circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test shows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
上傳時間： 2022-03-27
上傳用戶：
在傳統智能小車驅動電路設計中,較多考慮使用直流電機還是步進電機,電機功率、能耗等性能參數。使用具有armCortexM4內核的STM32嵌入式平臺控制四輪的4個直流電機。文章基于PWM技術及PID算法,對四輪進行精準地速度、轉向及啟停控制,實驗表明此小車具有優越各種地形適應能力。In the traditional intelligent car drive circuit design,DC motor or stepping motor,motor power,energy consumption and other performance parameters are considered.The four DC motors with four wheels are controlled by STM32 embedded platform with arm Cortex M4 kernel.Based on the PWM technology and PID algorithm,the accurate ground speed,steering,and start-stop control of the four wheels are carried out.The experiment shows that the vehicle has the superior adaptability to all kinds of terrains.
上傳時間： 2022-04-02
上傳用戶：
本文首次設計并驗證了基于macom三合一芯片設計的光模塊電路,該電路旨在提供一種滿足SFF-8472中規定的數字診斷功能的低成本SFP+模塊。電路采用激光器驅動、限幅放大器、控制器以及時鐘恢復單元集成的單芯片,在保證高精度數字診斷功能基礎上,實現了低成本高可靠的特點。該電路在光接收接口組件與激光器驅動和限幅放大器單元的限幅放大器部分之間接入濾波器來提高模塊的靈敏度及信號質量。在控制器單元的數字電位器的引腳上采用外加電阻的方式避免出現上電不發光的故障問題。該研究結果為下一代SFP-DD光模塊設計與開發工作,奠定了一定的理論與實踐基礎。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research results lay a theoretical and practical foundation for optical module design in high-speed data center.
上傳時間： 2022-04-03
上傳用戶：
The GL823K integrates a high speed 8051 microprocessor and a high efficiency hardware engine for the best data transfer performance between USB and flash card interfaces. Its pin assignment design fits to card sockets to provide easier PCB layout. Inside the chip, it integrates 5V to 3.3V regulator, 3.3V to 1.8V regulator and power MOSFETs and it enables the function of on-chip clock source (OCCS) which means no external 12MHz XTAL is needed and that effectively reduces the total BOM cost.
上傳時間： 2022-04-27
上傳用戶：qdxqdxqdxqdx
基于TMS320F28335的超聲波流量計硬件原理圖+軟件源碼本文以TMS320F28335 處理器為核心，設計一種用于管道流量測量的超聲波流量計。系統硬件由核心板，超聲波發射和接收電路，切換電路，超聲換能器，基于ADS805 的高速信號采集電路，人機交互以及電源等模塊構成。采用時差法進行管道流量測量，時差測量采用SCOT 加權的廣義互相關時延估計算法。本論文設計的超聲波流量計具有測量速度快、準確性好、成本低等優點。關鍵字：C2000，超聲波，流量，廣義互相關算法AbstractA kind of ultrasonic flowmeter using for the pipe flow measurement is designed based onTMS320F28335 in this paper. The system hardware consists of the following parts: the core board,ultrasonic signal transmitter and receiver circuits, switch circuit, ultrasonic transducer, signalacquisition circuit based on ADS805, human-computer interaction module and power supplymodule, etc. The system use the method of time difference for pipeline flow measurement and thetime difference is calculated by the time-delay algorithm of SCOT weighted generalizedcross-correlation. The ultrasonic flowmeter has the features of high testing speed, high precisionand low cost, etc.Keywords: C2000,Ultrasonic, Flow, Generalized Cross-Correlation Algorithm
標簽： tms320f28335 超聲波流量計
上傳時間： 2022-05-06
上傳用戶：
以STM32F103C8T6為核心,設計了無刷直流電機控制器硬件電路。電路主要包括IR2310構成的PWM驅動電路、IRF3808構成的逆變電路、增量式旋轉編碼構成的速度反饋電路?？刂破骶哂蠧AN和RS232通信接口,可與計算機或PLC構成速度或位置伺服系統。利用由xPC目標搭建的半實物仿真平臺對PI參數進行整定。測試了控制器的速度伺服響應性能,給定速度為2400rpm時,控制器響應時間為0.32s。實驗結果表明,系統工作可靠,穩定性好,響應速度快,可以滿足上肢康復機器人的機械臂速度控制性能要求。The hardware circuit of Brushless DC motor controller is designed by taking STM32F103C8T6 as the core,which mainly includes PWM driving circuits made up of IR2310,inverter circuit formed by IRF3808,speed feedback circuit composed of incremental rotary encoder and so on.Speed servo control system or position servo control system can be composed of BLDM controller with computer or PLC through CAN communication interface or RS232 serial communication interface.By using the hardware in the loop simulation platform built by xPC target,the PI parameters are set up.The Speed servo response performance of the controller is tested.When the speed is 2 400 rpm,the response time of the controller is 0...
上傳時間： 2022-05-07
上傳用戶：
基于DSP28335的永磁同步電機調速系統設計摘要（中英文） 本控制系統的設計是為了實現基于TMS320F28335的永磁同步電動機的調速系統，并把它引用到全電動注塑機當中。本系統使用SVPWM的控制方法，通過采樣電機電流和旋轉變壓器的位置信息，實現速度、電流雙閉環控制。通過TMS320F28335的硬件浮點處理核心，實現應用于永磁同步電機的浮點算法，去取代過去的定點算法，提高代碼效率。 Abstract: The control system is designed to realize TMS320F28335 based on the permanent magnet synchronous motor speed control system, and put it to quoting all electric of injection molding machine. The ystem of the control method used SVPWM, through the sampling motor current and rotating transformer 1. 引言1.1 設計背景及目的 本永磁同步電機調速系統是全電動注塑機的其中一個應用部分。全電動注塑機憑借著其節約能源、清潔、噪聲少、速度控制效果好、精度高、可重復性高、成本低等眾多優點，成為了當下高端注塑機發展的一個方向。 全電動注塑機的所有運動機構都采用交流伺服電動機驅動，一個穩定高效的永磁同步電動機驅動方案成為了全電動注塑機性能的一個總要部分。本次設計以適用于全電動注塑機的永磁同步電動機控制系統為目標進行設計，采用TI公司的TMS320F28335作為控制核心。憑借TMS320F28335高速的運算能力，適用于電動機控制的各種外設，以及TMS320F283XX特有的硬件浮點運算能力，進行永磁同步電動機的調速控制系統的設計。
上傳時間： 2022-05-08
上傳用戶：
基于DSP28035的高速永磁無刷直流電機驅動系統，包括論文和軟硬設計資料。摘要參賽作品為基于DSP28035的高速永磁無刷直流電機驅動系統。該系統以一臺額定轉速60 krpm的高速永磁無刷直流電機、交錯并聯的Buck電路以及全橋電路為硬件平臺，以DSP28035為控制核心，實現了調壓調速功能和基于坐標變換的無位置傳感器新技術。為實現該系統要求，本作品充分利用了DSP28035的資源例如：CLA模塊，模擬比較器、HPWM模塊以及AD轉換模塊等。AbstractThis work is the drive system for a high speed permanent magnet burshless dc motor based on DSP28035. The hardware platform consists of a BLDC motor(rated speed is 60000rpm), a Buck circuit and an inverter. Under the control of DSP28035, this system can achieve the goal of adjusting the motor’s speed with voltage and the function of sensorless control based on the coordinate transformation. By making full use of resources of the core, such as CLA, analog comparator, HPWM and AD converters, the whole system can meet the requirements.1 引言高速永磁無刷直流電機驅動系統由于基波頻率較高（一般在1kHZ以上），利用逆變橋斬波進行調速的控制方式通常會受到開關管開關頻率的限制，因此該系統多采用三相全橋前級加Buck電路進承擔調壓調速的功能，而三相全橋主要承擔邏輯換相的功能。然而，傳統Buck電路所需電感的體積較大，增加了系統的體積，降低了系統的功率密度。
上傳時間： 2022-05-08
上傳用戶：bluedrops
基于TMS320F28035芯片為控制核心的空間矢量異步電機變頻器 我們設計的異步電機變頻調速器以TMS320F28035芯片為控制核心，通過輸出三相PWM波控制智能功率模塊IPM驅動三相異步電機。我們使用空間矢量SVPWM算法，并對其進行了優化。采用檢測反電勢的方法省去了昂貴的光電編碼器，大大節省了成本。同時開創性的研發了自動根據運行環境調節的自適應變頻算法，使我們的變頻調速器可以在電網條件惡劣的鄉村山區工作，由此該變頻器已被一家民用水泵生產企業預訂。關鍵字 變頻器 TMS320f28035 IPM SVPWM In our design, the asynchronous machine inverter based on the chip of TMS320F28035 drives the three-Phase asynchronous machine by sending three-phase PWM waves to the IPM, which is short for the Intelligent-Power-Module. The SVPWM (space vector pulse width modulation) strategy is applied to our control algorithm and we optimize it mainly in two aspects. Firstly the inverter detects the speed by measuring the Back EMF instead of installing an expensive photoelectric encoder for costs reduction.
標簽： tms320f28035 芯片
上傳時間： 2022-05-08
上傳用戶：zhanglei193
