以C8051F020為核心處理器，設計無線傳感器網絡數據采集系統。系統采用SZ05-ADV型無線通訊模塊組建Zigbee無線網絡，結合嵌入式系統的軟硬件技術，完成終端節點的8路傳感器信號的數據采集。現場8路信號通過前端處理后，分別送入C8051F020的12位A/D轉換器進行轉換。經過精確處理、存儲后的現場數據，通過Zigbee無線網絡傳送到上位機，系統可達到汽車試驗中無線測試的目的。
Abstract:
This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
介紹一種基于CAN總線的牽引變電站自動化系統通訊規約的設計，CAN通訊規約采用標準幀，報文采用主動發送和發送查詢兩種處理形式。該設計在城市輕軌與地鐵牽引變電站中的應用表明：可實現間隔層和通訊處理層的數據快速、可靠的交換，提高牽引變電站的安全性和穩定性
。
Abstract:
This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
該系統由單片機89S52控制模塊，程控寬帶放大模塊，整形模塊，FPGA內頻率、相位差測量模塊等構成，采用等精度測頻法測出頻率和周期，可測量有效值為0.01～5V，頻率范圍1Hz～20MHz信號的頻率、周期信號，精度高達10-6。采用計數法測量相位差，該系統可測量有效值0.5～5V，頻率10Hz～100kHz信號的相位差，精度為1°。系統功能由按鍵控制，測量結果實時顯示，人機界面友好。
Abstract:
The system consists of the following functional blocks:89S52microcontroller controlling module,programmable amplifier module,comparator module,frequency and phase difference testing module in the FPGA.The system use the equal accuracy frequency-examining technique it measures frequency and circle of signal which its ranges is from1Hz to20MHz and the amplitude of which its range is from0.01Vrms to5Vrms,precision is up to10-6.Using of count method,the system detects the phase difference of signal,the amplitude of whic its range is from0.5Vrms to5Vrms and the frequency of which its ranges is from10Hz to100kHz,precision is up to1°,The system functions is controlled by certain keys,measurement results are displayed in real-time and it is friendly interface.
基于幅移鍵控技術ASK（Amplitude-Shift Keying），以C8051F340單片機作為監測終端控制器，C8051F330D單片機作為探測節點控制器，采用半雙工的通信方式，通過監控終端和探測節點的無線收發電路，實現數據的雙向無線傳輸。收發電路采用直徑為0.8 mm的漆包線自行繞制成圓形空心線圈天線，天線直徑為（3.4±0.3）cm。試驗表明，探測節點與監測終端的通信距離為24 cm，通過橋接方式，節點收發功率為102 mW時，節點間的通信距離可達20 cm。與傳統無線收發模塊相比，該無線收發電路在受體積、功耗、成本限制的場合有廣闊的應用前景。
Abstract:
Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The PCF8578 can function as a stand-alone LCDcontroller and driver for use in small systems. For larger systems it can be used inconjunction with up to 32 PCF8579s for which it has been optimized. Together these twodevices form a general purpose LCD dot matrix driver chip set, capable of driving displaysof up to 40960 dots. The PCF8578 is compatible with most microcontrollers andcommunicates via a two-line bidirectional bus (I2C-bus). Communication overhead isminimized by a display RAM with auto-incremented addressing and display bankswitching.
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· Uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
The CAT93C46 is a 1 kb Serial EEPROM memory device which isconfigured as either 64 registers of 16 bits (ORG pin at VCC) or 128registers of 8 bits (ORG pin at GND). Each register can be written (orread) serially by using the DI (or DO) pin. The CAT93C46 features aself−timed internal write with auto−clear. On−chip Power−On Resetcircuit protects the internal logic against powering up in the wrongstate.
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol.
The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts.
Features
MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC
Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF)
Parallel Port cable and a 14-conductor target cable
Full documentation on CD ROM
Integrated IAR Kickstart user interface which includes:
Assembler
Linker
Limulator
Source-level debugger
Limited C-compiler
Technical specifications:
Backwardly compatable with existing FET tool boards.
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE
The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
根據看門狗電路的原理，設計出簡單適用、性能可靠的1TrL型看門狗電路以及價格低廉、性能可靠的微功耗CMOS型看門狗電路，同時還介紹了常用的uP監視器O型看門狗電路。關鍵詞：看門狗電路；1TrL型；CMOS型Abstract：In accordance with the principle of WDT (Watch Dog Timer 1circuit，design a，IT．L type WTD circuit，it is a dimple an d applicable an d reliable on performanceo Design a CMOS type WTD circuit，it is low prices and mini-power consumption。Also the article describes a common uP type WTD circuit。Key word：WDT circuit；TFL type；CMOS typ e
