特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 計數暫時停止功能 3組報警功能 15BIT類比輸出功能 數位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 類比輸出解析度: 15 bit DAC 輸出反應速度: < 1/f+10ms(0-90%) 輸出負載能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 輸出之漣波: < 0.1% F.S. 通訊位址: "01"-"FF" 傳輸速度: 19200/9600/4800/2400 selective 通信協議: Modbus RTU mode 顯示幕: Red high efficiency LEDs high 14.22mm (.56") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-23
上傳用戶：redmoons
特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 前置量設定功能(二段設定)可選擇 數位化指撥設定操作簡易 計數暫時停止功能 3組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <5KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 顯示幕: Red high efficiency LEDs high 9.2mm (.36") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) ( 感應器電源 ) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-12
上傳用戶：909000580
無線交換機的出現，使無線局域網(WEAN)由傳統的分布式架構向集中管理式架構轉變，其中轉發功能也實現了從AP到無線交換機(AC)的遷移。如何利用AC更好地實現集中式流量轉發也成為無線交換機研發廠商主要考慮的問題之一。
上傳時間： 2013-10-14
上傳用戶：xwd2010
一種好用的微波小軟件
標簽： 模擬軟件
上傳時間： 2013-11-02
上傳用戶：wawjj
一種好用的微波小軟件
標簽： 模擬軟件
上傳時間： 2013-11-21
上傳用戶：asdkin
介紹了符合CCSDS標準的RS（255，223）碼譯碼器的硬件實現結構。譯碼器采用8位并行時域譯碼算法，主要包括了修正后的無逆BM迭代譯碼算法，錢搜索算法和Forney算法。采用了三級流水線結構實現，減小了譯碼器的時延，提高了譯碼的速率，使用了VHDL語言完成譯碼器的設計與實現。測試表明，該譯碼器性能優良，適用于高速通信。
上傳時間： 2013-12-13
上傳用戶：yzhl1988
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上傳時間： 2014-01-24
上傳用戶：s363994250
伺服驅動器
上傳時間： 2013-12-25
上傳用戶：偷心的海盜
特點 精確度0.1%滿刻度±1位數 可直接量測交直流電壓(AC/DC 20~265V)無需另接電源 精密濾波整流,均方根值校正 尺寸小(24x48x50mm),穩定性 分離式端子,配線容易 CE認證
上傳時間： 2013-11-05
上傳用戶：gaome
SL811開發資料_包含源程序_電路圖_芯片資料:SL811HS Embedded USB Host/Slave Controller.The SL811HS is an Embedded USB Host/Slave Controller capable of communicate with either full-speed or low-speed USB peripherals. The SL811HS can interface to devices such as microprocessors, microcontrollers, DSPs, or directly to a variety of buses such as ISA, PCMCIA, and others. The SL811HS USB Host Controller conforms to USB Specification 1.1.The SL811HS USB Host/Slave Controller incorporates USB Serial Interface functionality along with internal full-/low-speed transceivers.The SL811HS supports and operates in USB full-speed mode at 12 Mbps, or at low-speed 1.5-Mbps mode.The SL811HS data port and microprocessor interface provide an 8-bit data path I/O or DMA bidirectional, with interrupt support to allow easy interface to standard microprocessors or microcontrollers such as Motorola or Intel CPUs and many others. Internally,the SL811HS contains a 256-byte RAM data buffer which is used for control registers and data buffer.The available package types offered are a 28-pin PLCC (SL811HS) and a 48-pin TQFP package (SL811HST-AC). Both packages operate at 3.3 VDC. The I/O interface logic is 5V-tolerant.
上傳時間： 2013-12-22
上傳用戶：a82531317
