Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers Data Sheet AD8605/AD8606/AD8608The AD8605, AD8606, and AD86081 are single, dual, and quad rail-to-rail input and output, single-supply amplifiers. They feature very low offset voltage, low input voltage and current noise, and wide signal bandwidth. They use the Analog Devices, Inc. patented DigiTrim? trimming technique, which achieves
標簽： 運算放大器
上傳時間： 2022-02-02
上傳用戶：
The PW2606B is a front-end over voltage and over current protection device. It achieves wide inputvoltage range from 2.5VDC to 40VDC. The over voltage threshold can be programmed externally orset to internal default setting. The low resistance of integrated power path nFET switch ensures betterperformance for battery charging system applications. It can deliver up to 1A current to satisfy thebattery supply system. It integrates the over-temperature protection shutdown and auto-recoverycircuit with hysteresis to protect against over current events
標簽： pw2606b
上傳時間： 2022-02-11
上傳用戶：
文章提出了一種基于AT89S51單片機的智能家居系統的設計,該系統具有室內煤氣以及煙霧的檢測、家庭室內防盜等功能。文章詳細分析了系統的總體設計,詳盡分析并設計了煤氣傳感器模塊、煙霧傳感器模塊、人體紅外感應傳感器模塊、報警模塊等各硬件部分,并利用PROTUES軟件進行了系統仿真。仿真結果證明:系統具有成本低、效率高、操作方便等優點,達到了預期設計的效果。This paper presents the design of an intelligent home system based on AT89S51 microcontroller.The system has the functions of detecting indoor gas and smoke,guarding against theft in the home,and so on.The overall design of the system is analyzed in detail.The gas sensor module,smoke sensor module,human infrared sensor module,alarm module and other hardware parts are analyzed and designed in detail,and the system simulation is carried out using PROTUES software.The simulation results show that the system has the advantages of low cost,high efficiency,convenient operation and so on,and achieves the expected design effect.
上傳時間： 2022-03-28
上傳用戶：
為設計高效率、低損耗的PFC電路,本文基于UCC28019進行電路設計。以UCC28019輸出的PWM波形來控制Boost升壓斬波為核心電路,使電路中的電容交替地充放電、電感交替的儲存和釋放能量,最后實現在輸入AC20V~24V電壓情況下穩定輸出DC38V。測試結果表明,系統實現效率為95%左右,電壓調整率小于1%,電源功率因數0.99。交流輸入電壓為19.0-25.8 V時,輸出直流電壓穩定性較好,電感無明顯嘯叫且紋波小,具有一定的帶負載能力和實用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上傳時間： 2022-04-03
上傳用戶：
本文首次設計并驗證了基于macom三合一芯片設計的光模塊電路,該電路旨在提供一種滿足SFF-8472中規定的數字診斷功能的低成本SFP+模塊。電路采用激光器驅動、限幅放大器、控制器以及時鐘恢復單元集成的單芯片,在保證高精度數字診斷功能基礎上,實現了低成本高可靠的特點。該電路在光接收接口組件與激光器驅動和限幅放大器單元的限幅放大器部分之間接入濾波器來提高模塊的靈敏度及信號質量。在控制器單元的數字電位器的引腳上采用外加電阻的方式避免出現上電不發光的故障問題。該研究結果為下一代SFP-DD光模塊設計與開發工作,奠定了一定的理論與實踐基礎。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research results lay a theoretical and practical foundation for optical module design in high-speed data center.
上傳時間： 2022-04-03
上傳用戶：
