-
In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. Note that this does not include the PowerPC 602ª microprocessor which has a multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is speciÞed for 32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32 bits,and ßoating-point data types of 32 and 64 bits (single-precision and double-precision).1.1 Overview The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI bus,and main memory. This section provides a block diagram showing the major functional units of the 106 and describes brießy how those units interact.Figure 1 shows the major functional units within the 106. Note that this is a conceptual block diagram intended to show the basic features rather than an attempt to show how these features are physically implemented on the device.
標簽：
Bridge
Memory
Contr
MPC
上傳時間：
2013-10-08
上傳用戶：18711024007
-
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
標簽：
Exter
easy
work
with
上傳時間：
2013-10-27
上傳用戶：zhangyigenius
-
針對飛行模擬器座艙數據采集的復雜性，設計了一種基于以太網分布式的數據采集控制系統，該系統是RCM5700微處理器模塊上的以太網應用。在系統的基礎上具體討論了PoE技術的應用，在傳輸數據的網線上同時提供電流，提出并實現了一種包括輔助電源在內的完整可靠的PoE供電方案。設計采用美國國家半導體的LM5073和LM5576并根據不同的負載情況，進行穩定可靠的電壓轉換，以滿足數據采集電路的要求。實驗結果表明：該設計穩定可靠，滿足低于13 W的采集節點供電要求，提高了模擬器信號采集系統的通用性和標準化程度，避免了以往數據采集節點單獨繁瑣的電源設計。
Abstract:
Aiming at the complexity of large avion simulation and controlling，the simulator cabin distribute data collecting and control system was designed. This system is the application of RCM5700 on Ethernet. Based on this system，PoE technique that makes Ethernet can also provide power were expounded with emphasis and included FAUX design the PoE resolution was realized. To achieve the requirement of this system，LM5073 and LM5576 were used to DC-DC switch. From the data of experiment，the design filled the requirement of power-need of node whose power was lower than 13W. The application of the technique can advance the degree of simulation data collections currency and standardization and avoid designing additional power system.
標簽：
以太網
分布式
數據采集
控制系統
上傳時間：
2013-11-09
上傳用戶：xyipie
-
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty.
With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications.
Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
標簽：
lpc
datasheet
2292
2294
上傳時間：
2014-12-30
上傳用戶：aysyzxzm
-
This application note shows how a Xilinx CoolRunnerTM-II CPLD can be used as a simplelogical switch that can quickly and reliably select between different MPEG video sources. Thesource code for the design is available on the Xilinx website, and is linked from the “VHDLCode” section. The code can be expanded by the user to perform additional operations usingthe remaining CPLD resources
標簽：
CoolRunner-II
Xilinx
XAPP
CPLD
上傳時間：
2013-12-16
上傳用戶：qwer0574
-
The Virtex-4 features, such as the programmable IDELAY and built-in FIFO support, simplifythe bridging of a high-speed, PCI-X core to large amounts of DDR-SDRAM memory. Onechallenge is meeting the PCI-X target initial latency specification. PCI-X Protocol Addendum tothe PCI Local Bus Specification Revision 2.0a ([Ref 6]) dictates that when a target signals adata transfer, "the target must do so within 16 clocks of the assertion of FRAME#." PCItermination transactions, such as Split Response/Complete, are commonly used to meet thelatency specifications. This method adds complexity to the design, as well as additional systemlatency. Another solution is to increase the ratio of the memory frequency to the PCI-X busfrequency. However, this solution increases the required power and clock resource usage.
標簽：
PCI-X
XAPP
DIMM
708
上傳時間：
2013-11-24
上傳用戶：18707733937
-
本文論述了狀態機的verilog編碼風格,以及不同編碼風格的優缺點，Steve Golson's 1994 paper, "State Machine Design Techniques for Verilog and VHDL" [1], is agreat paper on state machine design using Verilog, VHDL and Synopsys tools. Steve's paper alsooffers in-depth background concerning the origin of specific state machine types.This paper, "State Machine Coding Styles for Synthesis," details additional insights into statemachine design including coding style approaches and a few additional tricks.
標簽：
Synthesis
Machine
Coding
Styles
上傳時間：
2013-10-12
上傳用戶：sardinescn
-
This document provides practical, common guidelines for incorporating PCI Express interconnect
layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10-
layer or more server baseboard designs. Guidelines and constraints in this document are intended
for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI
Express devices located on the same baseboard (chip-to-chip routing) and interconnects between
a PCI Express device located “down” on the baseboard and a device located “up” on an add-in
card attached through a connector.
This document is intended to cover all major components of the physical interconnect including
design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card
edge-finger and connector considerations. The intent of the guidelines and examples is to help
ensure that good high-speed signal design practices are used and that the timing/jitter and
loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect.
However, while general physical guidelines and suggestions are given, they may not necessarily
guarantee adequate performance of the interconnect for all layouts and implementations.
Therefore, designers should consider modeling and simulation of the interconnect in order to
ensure compliance to all applicable specifications.
The document is composed of two main sections. The first section provides an overview of
general topology and interconnect guidelines. The second section concentrates on physical layout
constraints where bulleted items at the beginning of a topic highlight important constraints, while
the narrative that follows offers additional insight.
標簽：
pci
PCB
設計規范
上傳時間：
2014-01-24
上傳用戶：s363994250
-
This simple SDI Notepad-like application demonstrates how, taking advantage of the MFC support for Unicode, to Turkmenize labels of the specified menu items. Actually, Turkmen is not supported by Windows 2000, therefore, to create such resources as menu so that strings in Turkmen could be displayed I had to invent an additional technique 這是一個與記事本類似的簡單的SDI應用程序，演示了怎樣使用MFC來支持 Unicode，對指定的菜單條目進行Turkmenize標簽化。實際上，Windwos 2000并不支持Turknen,因此,創建了那些菜單資源以便那些字符串可以在Turknen中顯示,為此我必須開發其它的技術。 來源: http://www.codeguru.com/advancedui/SDI_Note.html
標簽：
Notepad-like
demonstrates
application
advantage
上傳時間：
2013-11-26
上傳用戶：txfyddz
-
OXCC is a multipass, interpreting C compiler with several language extensions. It generates an Architecture Neutral Format (ANF) output and comes with a couple of example back ends. Programmers are expected to write additional back ends for their specific needs.
標簽：
interpreting
extensions
generates
multipass
上傳時間：
2015-04-12
上傳用戶：大三三
