Designers of signal receiver systems often need to performcascaded chain analysis of system performancefrom the antenna all the way to the ADC. Noise is a criticalparameter in the chain analysis because it limits theoverall sensitivity of the receiver. An application’s noiserequirement has a signifi cant infl uence on the systemtopology, since the choice of topology strives to optimizethe overall signal-to-noise ratio, dynamic range andseveral other parameters. One problem in noise calculationsis translating between the various units used by thecomponents in the chain: namely the RF, IF/baseband,and digital (ADC) sections of the circuit.
上傳時間： 2014-12-05
上傳用戶：cylnpy
The 14-bit LTC2351-14 is a 1.5Msps, low power SARADC with six simultaneously sampled differential inputchannels. It operates from a single 3V supply and featuressix independent sample-and-hold amplifi ers and a singleADC. The single ADC with multiple S/has enables excellentrange match (1mV) between channels and channel-tochannelskew (200ps).
上傳時間： 2014-12-23
上傳用戶：天誠24
Most circuit designers are familiar with diode dynamiccharacteristics such as charge storage, voltage dependentcapacitance and reverse recovery time. Less commonlyacknowledged and manufacturer specifi ed is diode forwardturn-on time. This parameter describes the timerequired for a diode to turn on and clamp at its forwardvoltage drop. Historically, this extremely short time, unitsof nanoseconds, has been so small that user and vendoralike have essentially ignored it. It is rarely discussed andalmost never specifi ed. Recently, switching regulator clockrate and transition time have become faster, making diodeturn-on time a critical issue. Increased clock rates aremandated to achieve smaller magnetics size; decreasedtransition times somewhat aid overall effi ciency but areprincipally needed to minimize IC heat rise. At clock speedsbeyond about 1MHz, transition time losses are the primarysource of die heating.
上傳時間： 2013-10-10
上傳用戶：誰偷了我的麥兜
Low power operation of electronic apparatus has becomeincreasingly desirable. Medical, remote data acquisition,power monitoring and other applications are good candidatesfor battery driven, low power operation. Micropoweranalog circuits for transducer-based signal conditioningpresent a special class of problems. Although micropowerICs are available, the interconnection of these devices toform a functioning micropower circuit requires care. (SeeBox Sections, “Some Guidelines for Micropower Designand an Example” and “Parasitic Effects of Test Equipmenton Micropower Circuits.”) In particular, trade-offs betweensignal levels and power dissipation become painful whenperformance in the 10-bit to 12-bit area is desirable.
上傳時間： 2013-10-22
上傳用戶：rocketrevenge
Over the past several years Linear Technology, the magazine, has come of age. From nothing, the publication has come into its own, as has its subscriber list. Many innovative circuits have seen the light of day in the pages of our now hallowed publication.
上傳時間： 2014-12-23
上傳用戶：crazyer
設計了水聲信號發生系統中的功率放大電路，可將前級電路產生的方波信號轉換為正弦信號，同時進行濾波、功率放大，使其滿足換能器對輸入信號的要求。該電路以單片機AT89C52，集成6階巴特沃思低通濾波芯片MF6以及大功率運算放大器LM12為核心，通過標準RS232接口與PC進行通信，實現信號增益的程控調節，對干擾信號具有良好的抑制作用。經調試該電路工作穩定正常，輸出波形無失真，在輸出功率以及放大增益、波紋系數等方面均滿足設計要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上傳時間： 2013-11-20
上傳用戶：qwe1234
The LM20, LM45, LM50, LM60, LM61, and LM62 are analog output temperature sensors. They have various output voltage slopes (6.25mV/°C to 17mV/°C) and power supply voltage ranges (2.4V to 10V).The LM20 is the smallest, lowest power consumption analog output temperature sensor National Semiconductor has released. The LM70 and LM74 are MICROWIRE/SPI compatible digital temperature sensors. The LM70 has a resolution of 0.125°C while the LM74 has a resolution of 0.625°C. The LM74 is the most accurate of the two with an accuracy better than ±1.25°C. The LM75 is National’s first digital output temperature sensor, released several years ago.
上傳時間： 2014-12-23
上傳用戶：yl8908
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
標簽： Converters Defini DAC
上傳時間： 2013-10-30
上傳用戶：stvnash
Power conversion by virtue of its basic role produces harmonics due to theslicing of either voltages or currents. To a large extent the pollution in theutility supply and the deterioration of the power quality has been generatedor created by non-linear converters. It is therefore ironic that power convertersshould now be used to clean up the pollution that they helped to create inthe first place.In a utility system, it is desirable to prevent harmonic currents (which resultin EMI and resonance problems) and limit reactive power flows (whichresult in transmission losses).Traditionally, shunt passive filters, comprised of tuned LC elements andcapacitor banks, were used to filter the harmonics and to compensate forreactive current due to non-linear loads. However, in practical applicationsthese methods have many disadvantages.
上傳時間： 2013-11-05
上傳用戶：AISINI005
高速數字系統設計下載pdf:High-Speed Digital SystemDesign—A Handbook ofInterconnect Theory and DesignPracticesStephen H. HallGarrett W. HallJames A. McCallA Wiley-Interscience Publication JOHN WILEY & SONS, INC.New York • Chichester • Weinheim • Brisbane • Singapore • TorontoCopyright © 2000 by John Wiley & Sons, Inc.speeddigital systems at the platform level. The book walks the reader through everyrequired concept, from basic transmission line theory to digital timing analysis, high-speedmeasurement techniques, as well as many other topics. In doing so, a unique balancebetween theory and practical applications is achieved that will allow the reader not only tounderstand the nature of the problem, but also provide practical guidance to the solution.The level of theoretical understanding is such that the reader will be equipped to see beyondthe immediate practical application and solve problems not contained within these pages.Much of the information in this book has not been needed in past digital designs but isabsolutely necessary today. Most of the information covered here is not covered in standardcollege curricula, at least not in its focus on digital design, which is arguably one of the mostsignificant industries in electrical engineering.The focus of this book is on the design of robust high-volume, high-speed digital productssuch as computer systems, with particular attention paid to computer busses. However, thetheory presented is applicable to any high-speed digital system. All of the techniquescovered in this book have been applied in industry to actual digital products that have beensuccessfully produced and sold in high volume.Practicing engineers and graduate and undergraduate students who have completed basicelectromagnetic or microwave design classes are equipped to fully comprehend the theorypresented in this book. At a practical level, however, basic circuit theory is all thebackground required to apply the formulas in this book.
上傳時間： 2013-10-26
上傳用戶：縹緲
