manufacturers of electronic systems that require power
conversion are faced with the need for higher-density dc-to-dc
converters that perform more efficiently,
Many of the designations used by manufacturers and sellers to distinguish their products are
claimed as trademarks. Where those designations appear in this book and Addison Wesley
Longman Inc., was aware of a trademark claim, the designations have been printed in initial caps
or all caps.
The authors and publisher have taken care in the preparation of this book, but make no
expressed or implied warranty of any kind and assume no responsibility for errors or omissions.
No liability is assumed for incidental or consequential damages in connection with or arising out
of the use of the information or programs contained herein.
The publisher offers discounts on this book when ordered in quantity for special sales. For more
information, please contact:
Abstract: Most magnetic read head data sheets do not fully specify the frequency-dependent components andare often vague when specifying other key parameters. In some cases, the specifications of two very similarheads from two different manufacturers might be quite different in terms of parameters specified and omitted.The limitations in the data sheets make designing an optimum card reading system unnecessarily difficult andtime consuming. This document outlines a strategy to overcome the above shortcomings and offers guidelinesto overcome the noise issues.
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
介紹一種以Atmel公司的Attiny13為處理器的投影儀防盜器設計方案。該防盜器具有功耗低，功能完整，防盜效果良好等特點，除具有報警功能外，防盜器還具有以無線方式向主機發送報警信號的功能。采用315MHz發射模塊實現無線信號發送。該投影儀防盜器可適應眾多廠家生產的防盜器主機。
Abstract:
This paper introduces the design scheme of overhead projector's anti-theft device which users ATMEL company’s Attiny13as processor.This anti-theft device features low powerloss，functional integrity，good effect of anti-theft.In addition to its own with alarm functions，the anti-theft device also has alarm function which can send alarm signal to the host through wireless way.It sends wireless signal using315MHz transmitting module，so this overhead projector’s anti-theft device is adapted to anti-theft device host produced by many manufacturers.
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with standard series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
There are many manufacturers of dot matrix LCD modules. However, most of these displaysare similar. They all have on-board controllers and drivers capable of displaying alpha numericsand a wide variety of other symbols (including Japanese "Katakana" characters). The internaloperation of LCD controller devices is determined by signals sent from a central processing unit(in this case, a CoolRunner-II CPLD).
手機文件瀏覽程序的另外一個版本！ SMan is a system utility that manages your UIQ device. It provides functionality which manufacturers did not provide or which are difficult or impossible to do manually. SMan helps keep your UIQ device running in a "healthy" state and, to a certain degree, allows you to customize the system behaviour of your device.
The I2C Memory Model is a generic Proteus VSM model designed to model the timing and functionality of I2C memory devices from a wide range of manufacturers.
CANopen is a networking system based on the CAN serial bus.
CANopen assumes that the device’s hardware has a CAN transceiver
and CAN controller as specified in ISO 11898.
CANopen profile family specifies standardized communication
mechanisms and device functionality. The profile family is available
and maintained by CAN in Automation (CiA), the international users’
and manufacturers’ group and may be implemented license-free.
