黑金CYCLONE4 EP4CE6F17C8 FPGA開發板ALTIUM設計硬件工程（原理圖+PCB+AD集成封裝庫）,Altium Designer 設計的工程文件，包括完整的原理圖及PCB文件，可以用Altium(AD)軟件打開或修改，可作為你產品設計的參考。集成封裝器件型號列表：Library Component Count : 50Name Description----------------------------------------------------------------------------------------------------1117-3.3 24LC04B_0 4148 BAV99 CAP NP_Dup2CAP NP_Dup2_1 CAP NP_Dup2_2CP2102_0 C_Dup1 C_Dup1_1C_Dup2 C_Dup3 C_Dup4 C_Dup4_1 Circuit Breaker Circuit BreakerConnector 15 Receptacle Assembly, 15-Pin, Sim Line ConnectorDS1302_8SO EC EP4CE6F17C8 Cyclone IV Family FPGA, 2V Core, 179 I/O Pins, 2 PLLs, 256-Pin FBGA, Speed Grade 8, Commercial GradeEP4CE6F17C8_1 Cyclone IV Family FPGA, 2V Core, 179 I/O Pins, 2 PLLs, 256-Pin FBGA, Speed Grade 8, Commercial GradeFuse 2 FuseHEX6HY57651620/SO_0 Header 2 Header, 2-PinHeader 9X2 Header, 9-Pin, Dual rowINDUCTOR JTAG-10_Dup1 KEYB LED LED_Dup1 M25P16-VMN3PB 16 Mb (x1) Automotive Serial NOR Flash Memory, 75 MHz, 2.7 to 3.6 V, 8-pin SO8 Narrow (MN), TubeMHDR2X20 Header, 20-Pin, Dual rowMiniUSBB OSCPNP R RESISTOR RN RN_Dup1 R_Dup1 R_Dup2 R_Dup3 R_Dup5R_Dup6 SD SPEAKERSRV05-4SW KEY-DPDT ZTAbattery
標簽：
黑金
cyclone4
ep4ce6f17c8
fpga
上傳時間：
2021-12-22
上傳用戶：
Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include
most small appliances, test equipment, and
other devices that plug into a branch outlet
or socket. The 34401A may be used to make
measurements with the HI and LO inputs
connected to mains in such devices, or to
the branch outlet itself (up to 300 VAC).
However, the 34401A may not be used with
its HI and LO inputs connected to mains in
permanently installed electrical devices
such as the main circuit-breaker panel,
sub-panel disconnect boxes, or permanently
wired motors. Such devices and circuits are
subject to overvoltages that may exceed the
protection limits of the 34401A.
Note: Voltages above 300 VAC may be measured only in circuits that are isolated from
mains. However, transient overvoltages are
also present on circuits that are isolated
from mains. The Agilent 34401A are
designed to safely withstand occasional
transient overvoltages up to 2500 Vpk. Do
not use this equipment to measure circuits
where transient overvoltages could exceed
this level.
Additional Notices
Waste Electrical and
Electronic Equipment (WEEE)
Directive 2002/96/EC
This product complies with the WEEE Directive (2002/96/EC) marking requirement.
The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic
household waste.
Product Category: With reference to the
equipment types in the WEEE directive
Annex 1, this product is classified as a
"Monitoring and Control instrumentation"
product.
Do not dispose in domestic household
waste.
To return unwanted products, contact your
local Agilent office, or see
www.agilent.com/environment/product
for more information.
Agilent 34138A Test Lead Set
The Agilent 34401A is compatible with the
Agilent 34138A Test Lead Set described
below.
Test Lead Ratings
Test Leads - 1000V, 15A
Fine Tip Probe Attachments - 300V, 3A
Mini Grabber Attachment - 300V, 3A
SMT Grabber Attachments - 300V, 3A
Operation
The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of
the Test Leads.
Maintenance
If any portion of the Test Lead Set is worn or
damaged, do not use. Replace with a new
Agilent 3413
標簽：
agilent
上傳時間：
2022-02-20
上傳用戶：
