介紹了基于單片機航空交流電參數測試儀的系統設計。以Silicon Labs公司的C8051F005單片機為核心設計出數據采集板，通過RS-232串口與上位機通訊。運用Lab Windows/CVI編寫的上位機軟件實現信號的檢測以及波形和數據的顯示，給出了測試儀硬件電路的組成和軟件流程圖。本系統具有硬件結構簡單、容易實現和成本低等特點，在實際應用中其穩定性、精確性均能滿足客戶要求。 Abstract: The design of aeronautics AC parameters tester based on the single-chip is introduced.The core component of data acquisition board is C8051F005 single chip of Silicon Labs Company,and communication with PC through RS-232. The signal processing software programmed with LabWindows/CVI can be used successfully to fulfill inspection of signal and display of the waveform and data. The hardware and software configuration of test instrument are provided.The hardware of the system is simple, and can be easily realized.The stability and precision of the measurement instrument are enough to meet the requirements.
上傳時間： 2013-11-18
上傳用戶：wang5829
介紹了電力操作電源與智能電池巡檢系統的特點，給出了一種基于超低功耗單片機MSP430 F149針對中小型變電站自動化運行的專用設備的基本設計原理及實現方法，最后給出了詳細硬件構成和軟件實現。該系統能滿足中小型變電站安全、可靠、自動運行的要求，并通過與上位機的串行通信實現變電站的遠程管理和控制。 Abstract: The characters of the intelligent battery data logging system of the electric operation power are introduced.The basic design principle and the implemented methods of the special equipment which only designed for the middle or small transformer substation based on MSP430F149 are prescribed. Finally, the hardware block diagram and the software flow chart are also given. The function that the system finally needs to realize can basically meet with the middle or small transformer substation’s satisfy, reliably,and automatic running.And it can also realize the transformer substation long-distance management and control by serial communicating with the host computer.
上傳時間： 2013-11-25
上傳用戶：黃華強
介紹一種以MSP430單片機為基礎的智能頻率測量系統，采用硬件邏輯與軟件指令相結合的方式控制閘門，實現0 MHz~10 MHz范圍內無檔切換的等精度測量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上傳時間： 2013-10-28
上傳用戶：dbs012280
在介紹基于MSP430單片機的指紋保險柜工作原理的基礎上，從系統軟件設計的角度出發，詳細介紹了指紋保險柜軟件的總體分析過程、程序結構的設計以及代碼的編寫，給出了按鍵管理流程和部分源代碼。 Abstract: On basis of the operating principle of MSP430 microcontroller-based fingerprint safe,the general analyzing process,program designing and code compiling of the fingerprint safe software are introduced mainly,and the key-press flows chart and some codes according to the system software designing are put forward.
上傳時間： 2014-12-27
上傳用戶：gaojiao1999
介紹基于ATmega8型單片機的溫度測量及加熱控制系統。分析系統的工作原理，詳盡討論系統的硬件電路和軟件流程。實驗證明，該系統工作可靠，穩定性高。 Abstract: The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyzed.The design principles of hardware and software are also discussed in detail.This system has been testified and it works steady and reliably.
上傳時間： 2013-11-21
上傳用戶：caiguoqing
利用Atmel公司的ATmega168微處理器，采用A/D轉換方式來實現按摩椅控制器的鍵盤接口，通過在硬件電路中巧妙地選擇電阻，在軟件設計中采用數字濾波、二分法和區間鑒定等方法，靈敏可靠地實現了按摩椅中30個按鍵的處理。給出了硬件電路設計和軟件設計思想以及部分匯編代碼。 Abstract: This paper chooses A/D conversion method to realize the keyboard interface of the controller by using ATmega168 microchip from Atmel Company.It accomplishes 30-key dealing sensitively and reliably in massage chair through skillfully selecting resistors in hardware circuit and using digital filter,dichotomy and area-judging method in software design.The hardware design circuit, software design idea and partly assembles code are presented mainly.
上傳時間： 2014-01-10
上傳用戶：咔樂塢
以S3C825A為例介紹三星公司SAM8系列單片機的內部結構及其軟件開發環境，詳細描述采用混合編程法來對SAM8系列單片機進行軟件設計的一般方法，最后給出用混合編程法對S3C825A進行軟件設計的具體應用實例。 Abstract: With S3C825A,this paper firstly introduces the SAM8 series single-chip microcontrollers and their software development environment, then introduces mixed programming technology for SAM8 series single-chip microcontrollers. In the end, the application program is also given.
上傳時間： 2013-12-09
上傳用戶：ZZJ886
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· Uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
上傳時間： 2013-11-08
上傳用戶：laozhanshi111
針對當前安檢力學試驗機所能完成的試驗種類單一、自動化程度低等問題，提出一種以ATmega128單片機為核心控制器的安檢力學試驗機的設計。詳細闡述了該安檢力學試驗機各個組成部分的設計原理和方案，并且給出了各部分的軟件設計思想和操作流程。經過大量測試試驗表明：設計的安檢力學試驗機可以完成多達十余種的力學安檢試驗，完全符合相關國家標準，并且具有數據采集精度高、傳輸速度快、操作安全簡便等特點，實現了安檢設備的多功能化、數字化和自動化。 Abstract: Currently， many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems， a new kind of mechanical security testing machine， using ATmega128 micro-controller as its core controller， has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail， and the software architecture and the operation processes of each part are given. After having done many testing， we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The operation of the machine is simple and safe. In general， this machine is a multi-functional， highly automatic， digitalized security testing device.
上傳時間： 2013-11-05
上傳用戶：a67818601
Information in this document is subject to change without notice and does notrepresent a commitment on the part of the manufacturer. The software describedin this document is furnished under license agreement or nondisclosureagreement and may be used or copied only in accordance with the terms of theagreement. It is against the law to copy the software on any medium except asspecifically allowed in the license or nondisclosure agreement. The purchasermay make one copy of the software for backup purposes. No part of this manualmay be reproduced or transmitted in any form or by any means, electronic ormechanical, including photocopying, recording, or information storage andretrieval systems, for any purpose other than for the purchaser’s personal use,without written permission.
上傳時間： 2014-12-27
上傳用戶：Tracey
