-
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
標簽：
USB
電源管理IC
方案
上傳時間：
2013-11-02
上傳用戶：名爵少年
-
Although recent popular attention is focused on LithiumIon batteries, one must not forget that other batterychemistries, such as Nickel Cadmium (NiCd) and NickelMetal Hydride (NiMH) have advantages in rechargeablepower systems. Nickel-based batteries are robust, capableof high discharge rates, have good cycle life, do notrequire special protection circuitry and are less expensivethan Li-Ion. Among the two, NiMH batteries are rapidlyreplacing NiCd because of their higher capacity (40% to50% more) and the environmental concerns of the toxiccadmium contained in NiCd batteries.
標簽：
NiMH
NiCd
獨立
電池充電
上傳時間：
2013-11-04
上傳用戶：qq10538412
-
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
標簽：
DC
降壓
升壓型
控制器
上傳時間：
2013-10-21
上傳用戶：ljt101007
-
The LTC®3562 quad output step-down regulator is designedfor multicore handheld microprocessor applications thatoperate from a single Li-Ion battery. Its four monolithic, higheffi ciency buck regulators support Intel’s mobile CPU P-Stateand C-State energy saving operating modes. The outputvoltages are independently controllable via I2C, and eachoutput can be independently started and shut down. Designerscan choose from power saving pulse-skipping mode orBurst Mode® operation, or select low noise LDO mode. Thespace-saving LTC3562 is available in a 3mm × 3mm QFNpackage and requires few external components.
標簽：
DC
442
I2C
DN
上傳時間：
2013-10-07
上傳用戶：1583060504
-
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
標簽：
436
DN
全橋
壓電
上傳時間：
2013-11-18
上傳用戶：hulee
-
Automotive power systems are unforgiving electronicenvironments. Transients to 90V can occur when thenominal voltage range is 10V to 15V (ISO7637), along withbattery reversal in some cases. It’s fairly straightforwardto build automotive electronics around this system, butincreasingly end users want to operate portable electronics,such as GPS systems or music/video players,and to charge their Li-Ion batteries from the automotivebattery. To do so requires a compact, robust, effi cientand easy-to-design charging system
標簽：
464
USB
DN
高效率
上傳時間：
2013-11-04
上傳用戶：wfl_yy
-
The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2Cprogrammability and USB On-The-Go for systems suchas tablet PCs and other high power density applications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forlithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionality is controlled directly from theUSB connector ID pin.
標簽：
高電流
便攜式產品
電池充電器
方案
上傳時間：
2013-10-09
上傳用戶：hanhanj
-
匯編器在微處理器的驗證和應用中舉足輕重，如何設計通用的匯編器一直是研究的熱點之一。本文提出了一種開放式的匯編器系統設計思想，在匯編語言與機器語言間插入中間代碼CMDL（code mapping description language）語言，打破匯編語言與機器語言的直接映射關系，由此建立起一套描述匯編語言與機器語言的開放式映射體系。基于此開放式映射體系開發了一套匯編器系統，具有較高層次上的通用性和可移植性。【關鍵詞】指令集，CMDL，匯編器，開放式
Design of Retargetable Assembler System Liu Ling Feng Wen Nan Wang Ying Chun Jiang An Ping Ji Li Jiu IME of Peking University, 100871【摘要】An assembler plays a very important role in the field of microprocessor verifications and applications, thus how to build a retargetable assembler system has been a hotspot in this field for long time. This paper presents a new method about the retargetable assembler system design.It provides a kind of language CMDL, code mapping description language. During the process of assembling, assembler languages are firstly translated to CMDL, and then mapped to the machine codes. In an other word, CMDL is inserted between assembler languages and machine codes during the translation procedure. As a medium code, CMDL has a lot of features, such as high extraction, strong descript capabilities. It can describe almost all attributes of assembler languages. By breaking the direct mapping relationship between assembler languages and machine codes, the complexities of machine codes are hided to the users, therefore, the new retargetable assembler system has higher retargetable level by converting the mapping from assembler languages and machine codes to assembler languages and CMDL, and implementationof it becomes easier. Based on the new mapping system structure, a retargetable assemblersystem is developed. It proved the whole system has good retargetability and implantability.【關鍵詞】instruction set, symbol table, assembler, lexical analysis, retargetability
標簽：
開放式
匯編器
上傳時間：
2013-10-10
上傳用戶：meiguiweishi
-
LTC1732 是LINEAR TECHNOLOGY 公司推出的鋰離子電池充電控制集成電路芯片。它具有電池插入檢測和自動低壓電池充電功能。文章介紹了該芯片的結構、特點、工作原理及應用信息，給出了典型的應用電路。
LTC1732 是LINEAR TECHNOLOGY 公司生產的鋰-離子（Li-離子）電池恒流/恒壓線性充電控制器。它也可以對鎳-鎘（NiCd）和鎳-氫（NiMH）電池恒流充電。其充電電流可通過外部傳感電阻器編程到7%（最大值）的精度。最終的浮動電壓精度為1%。利用LTC1732 的SEL 端可為4.1V 或4.2V 電池充電。當輸入電源撤消后，LTC1732 可自動進入低電流睡眠狀態，以使消耗電流下降到7μA。LTC1732 的內部比較器用于檢測充電結束條件（C/10），而總的充電時間則是通過可編程計時器的外部電容來設置的。在電池完全放電后，控制器將自動以規定電流的10%對被充電電池進行慢速充電直到電池電壓超過2.457V。當放電后的電池插入充電器或當輸入電源接通時，LTC1732 將開始重新充電。另外，如果電池一直插入在充電器且在電池電壓降到3.8V（LTC1732-4）或4.05V（LTC1732-4.2）以下時，充電器也將開始重新充電。LTC1732 的其它主特點如下：●具有1%的預置充電電壓精度；●輸入電壓范圍4.5V～12V；●充電電流可編程控制；●具有C/10 充電電流檢測輸出；●可編程控制充電終端計時；●帶有低電壓電池自動小電流充電模式；●可編程控制恒定電流接通模式；●具有電池插入檢測和自動低壓電流充電功能；●帶有輸入電源（隔離適配器）檢測輸出；●LTC1732-4.2 型器件的再充電閾值電壓為4.05V；●LTC1732-4 型器件的再充電閾值電壓為3.8V。
標簽：
1732
LTC
離子
電池充電
上傳時間：
2013-11-12
上傳用戶：semi1981
-
作者RICHARD CHI-HSI LI，結合自己20年RF設計經驗，整理的RF設計技術與經驗，工程性很強，從最基本的LNA、MIXERS、差分對等講起，涉及到阻抗匹配，接地，天線設計，RF系統分析，是一本很不錯的書。英文版
標簽：
RF設計
經驗
上傳時間：
2013-10-30
上傳用戶：ve3344
