CAN與RS232轉換節點的設計與實現
介紹將CAN總線接口與RS232總線接口相互轉換的設計方法和2種總線電平轉換關系，實現CAN總線與各模塊的接口設計，制定了相應的軟硬件設計方案，并給出軟件設計流程圖以及部分硬件設計原理圖。為CAN總線與RS232總線互聯提供了一種方法，對CAN總線與RS232總線接口設備的互聯和廣泛應用的實現具有重要意義。關鍵詞：CAN總線；RS-232總線；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
（Portmon is an application that lets you monitor serial and parallel activity on your local system, or any computer on the network that you can reach via TCP/IP. It is the most powerful tool available for tracking down port-related configuration problems and analyzing application port usage.）
中文版詳情瀏覽：http://www.elecfans.com/emb/fpga/20130715324029.html
Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture
The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications.
The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation.
Some of the UltraScale architecture breakthroughs include:
• Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50%
• Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system speed and capability
• Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization
• 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard
• Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets
• Greatly enhanced DSP and packet handling
The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
This application note provides users with a general understanding of the SVF and XSVF fileformats as they apply to Xilinx devices. Some familiarity with IEEE STD 1149.1 (JTAG) isassumed. For information on using serial Vector Format (SVF) and Xilinx serial Vector Format(XSVF) files in embedded programming applications
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。
Abstract:
In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function
Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and both implementation and simulation scripts
The XPS Ethernetlite peripheral does not provide any mechanism to access the Ethernet PHYregisters. These registers are used to configure auto negotiation parameters and to obtain PHYstatus. This application note provides reference systems and associated software to accessPHY registers by connecting the serial management bus signals MDC and MDIO to GPIOswhich the software controls directly.
