實時時鐘是微機保護裝置的重要部件，在討論PCF8583結構與功能的基礎上，提出采用dsPIC33F系列微處理器與串行I2C時鐘PCF8583的接口設計方案，給出了相應的接口電路與軟件流程。該設計方案結構簡單，可靠性高，開發周期短，具有一定的實用與參考價值。所設計的微機保護裝置已投入現場運行，效果良好。 Abstract: Real-time clock chip is an important part in microcomputer protection device.Based on discussing the structure and function of PCF8583，a new interface scheme which uses dsPIC33F microprocessor and serial clock chip（I2C）PCF8583is proposed.The method of the circuit design and the main software flow are introduced in this paper.The scheme has simple structure，higher reliability and shorter exploitation cycle，so has definite practicality or reference value.The microcomputer protection device has been put into operation with better effects.
上傳時間： 2013-11-18
上傳用戶：Thuan
針對盤山路存在的轉彎盲區，即在轉彎時司機無法得知彎路對面是否有車輛通過，設計一種基于C8051F310的山路轉彎預防警示系統。該系統利用一階濾波算法檢測山路轉彎時是否有車輛通過。運用該算法可增強系統檢測的實時性，提高檢測機動車輛的靈敏度，同時大大減少環境溫度對檢測的干擾。試驗表明該系統能夠正確指示出在山路轉彎時是否有車輛通過，目前該系統已安裝在盤山路上，可大大減少事故的發生率。 Abstract: Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
上傳時間： 2013-10-10
上傳用戶：歸海惜雪
介紹了采用ATmega48單片機實現三相無刷直流電機控制器的方法。利用Atmega48獲得帶死區的脈寬調制（PWM）、霍爾傳感器的換相處理、正弦驅動信號的產生和電機轉速的控制等功能。采用該方法的優點是所需的外圍器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上傳時間： 2013-12-09
上傳用戶：330402686
氣壓是氣象監測中的一個重要參數，提出了一種氣壓數據采集模塊設計方案，該模塊采用數字氣壓傳感器MS5534B、MSP430單片機MSP430F2272和帶實時時鐘（RTC）64 KB鐵電存儲器。通過低功耗軟件設計方法以微安級整體平均功耗實現了氣壓數據的采集和存儲，適合電池供電的連續高精度氣壓采集應用。給出了模塊的軟硬件設計以及MS5534B的性能指標和使用經驗。 Abstract: Air pressure is an important parameter in weather monitor.This paper futs forward a new design scheme of low power-air pressure data acquisition module.The module uses a digital output barometer sensor MS5534B,MSP430 microcontroller MSP430F2272 and integrated RTC 64KB FRAM,precision air pressure measurement and storage chip.Another point of this module is low power consumption, so it is well suited for battery powered air pressure data acquisition applications. At the same time,the software and hardware deign of module is presented,And the speciaties and use notices of MS5534B are given.
上傳時間： 2014-12-27
上傳用戶：drink！
介紹一種以MSP430單片機為基礎的智能頻率測量系統，采用硬件邏輯與軟件指令相結合的方式控制閘門，實現0 MHz~10 MHz范圍內無檔切換的等精度測量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上傳時間： 2013-10-28
上傳用戶：dbs012280
對于瀝青混凝土攤鋪機自動找平控制系統來說，數字式控制系統的研制是目前的一個方向。介紹了一種基于CAN總線的數字式自動找平控制系統。該系統以CAN總線作為通信方式，PWM控制信號通過C8051F040單片機內部PCA可編程計數器陣列產生，并具有結構簡單、信號穩定、實時性強、易擴展的特點。通過硬件實現和系統運行達到了比較理想的控制效果，驗證了系統的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 microcontroller. The system is simple, stable, real-time and expansive.
上傳時間： 2013-10-09
上傳用戶：ligi201200
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
上傳時間： 2013-11-08
上傳用戶：laozhanshi111
為了在工業生產及過程控制中準確測量溫度，設計了一種基于低功耗MSP430單片機的數字溫度計。整個系統通過單片機MSP430F1121A控制DS18B20讀取溫度，采用數碼管顯示，溫度傳感器DS18B20與單片機之間通過串口進行數據傳輸。MSP430系列單片機具有超低功耗，且外圍的整合性高，DS18B20只需一個端口即可實現數據通信，連接方便。通過多次實驗證明，該系統的測試結果與實際環境溫度一致，除了具有接口電路簡單、測量精度高、誤差小、可靠性高等特點外，其低成本、低功耗的特點使其擁有更廣闊的應用前景。 Abstract: In order to obtain accurate measuring temperature in industrial production and process control， a digital thermometer based on MSP430 MCU is designed. The system uses MSP430F1121A MCU to control DS18B20， and gets the temperature data， which is displayed on the LED. The temperature sensor DS18B20 and MCU transmit data through serial communication. MSP430 series has ultra-low power and high integration， DS18B20 only needs one port to achieve data communication. Through many experimental results prove， this system is consistent with actual environment temperature. The system has characteristics of interface circuit simple， high measuring accuracy， minor error， high reliability， besides， the characteristics of low cost and low power make it having vaster application prospect.
上傳時間： 2013-10-16
上傳用戶：wettetw
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上傳時間： 2013-10-26
上傳用戶：fengweihao158@163.com
NEC 16位MCU參考手冊 The 78K0R/IC3 is a 16-bit single-chip microcontroller that uses a 78K0R CPU core and incorporates peripheral functions, such as ROM/RAM, a multi-function timer, a multi-function serial interface, an A/D converter, a programmable gain amplifier (PGA), a comparator, a real-time counter, and a watchdog timer.
上傳時間： 2013-11-02
上傳用戶：努力努力再努力
