為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題,研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心,并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集,并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示,也可以通過紅外方式和PC機進行通訊,在PC機上進行信號的處理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current,signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上傳時間: 2013-11-06
上傳用戶:yy_cn
在介紹基于MSP430單片機的指紋保險柜工作原理的基礎上,從系統軟件設計的角度出發,詳細介紹了指紋保險柜軟件的總體分析過程、程序結構的設計以及代碼的編寫,給出了按鍵管理流程和部分源代碼。 Abstract: On basis of the operating principle of MSP430 microcontroller-based fingerprint safe,the general analyzing process,program designing and code compiling of the fingerprint safe software are introduced mainly,and the key-press flows chart and some codes according to the system software designing are put forward.
上傳時間: 2014-12-27
上傳用戶:gaojiao1999
介紹基于ATmega8型單片機的溫度測量及加熱控制系統。分析系統的工作原理,詳盡討論系統的硬件電路和軟件流程。實驗證明,該系統工作可靠,穩定性高。 Abstract: The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyzed.The design principles of hardware and software are also discussed in detail.This system has been testified and it works steady and reliably.
標簽: ATmgea8 單片機 加熱控制
上傳時間: 2013-11-21
上傳用戶:caiguoqing
對于瀝青混凝土攤鋪機自動找平控制系統來說,數字式控制系統的研制是目前的一個方向。介紹了一種基于CAN總線的數字式自動找平控制系統。該系統以CAN總線作為通信方式,PWM控制信號通過C8051F040單片機內部PCA可編程計數器陣列產生,并具有結構簡單、信號穩定、實時性強、易擴展的特點。通過硬件實現和系統運行達到了比較理想的控制效果,驗證了系統的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 microcontroller. The system is simple, stable, real-time and expansive.
標簽: CAN 總線 數字式 控制系統設計
上傳時間: 2013-10-09
上傳用戶:ligi201200
介紹以P87LPC764型單片機為核心的延時型漏電繼電器設計方案。該方案可供用戶選擇實現額定動作電流和5倍額定動作電流下不同的延時動作時間,并有重合閘設定選擇功能。解決了以往傳統分立元件帶來的延時時間離散性大且不易實現的弊端。 Abstract: In this paper, the delay leakage relay based on P87LPC764 is introduced in detail. This system provides different relay times at rating current and 5× rating current for users and also offers superposition brake set selection function. So that it resolves many traditional problems.
上傳時間: 2013-11-08
上傳用戶:zhaiye
介紹了CAN總線和P87C591單片機的特點,給出了基于P87C591單片機的信號采集節點的軟、硬件設計,指出了硬件電路設計中應注意的問題,在軟件設計中重點介紹了節點初始化、報文發送和報文接收等子程序。 Abstract: The features of CAN Bus and the microcontroller P87C591 are introduced, and the design of hardware circuit and soft configuration of the signals collection node based on P87C591 are presented. The problems in designing hardware circuit are discussed.Initialization subprogram, transmiting subprogram and receiving subprogram are emphasized in soft configuration.
標簽: P87C591 信號采集 節點
上傳時間: 2013-11-03
上傳用戶:BIBI
基于幅移鍵控技術ASK(Amplitude-Shift Keying),以C8051F340單片機作為監測終端控制器,C8051F330D單片機作為探測節點控制器,采用半雙工的通信方式,通過監控終端和探測節點的無線收發電路,實現數據的雙向無線傳輸。收發電路采用直徑為0.8 mm的漆包線自行繞制成圓形空心線圈天線,天線直徑為(3.4±0.3)cm。試驗表明,探測節點與監測終端的通信距離為24 cm,通過橋接方式,節點收發功率為102 mW時,節點間的通信距離可達20 cm。與傳統無線收發模塊相比,該無線收發電路在受體積、功耗、成本限制的場合有廣闊的應用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller, using half-duplex communication mode, this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter (3.4±0.3) cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm,the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules, the circuit has wide application prospect in small size, low cost and low power consumption and other characteristics.
標簽: C8051F 單片機 無線收發 電路設計
上傳時間: 2013-10-19
上傳用戶:xz85592677
在需要實時大量輸入漢字的顯示控制處理應用中,利用傳統單片機實現顯示控制的設計方法是較難實現的。帶漢字字庫的液晶模塊的使用使得小容量ROM單片機的大量漢字信息輸入與顯示成為可能。提出了針對漢字字庫編碼的二級索引拼音輸入檢索方法,介紹了以ST7920作為控制器的帶漢字字庫的液晶顯示模塊的接口方法及漢字顯示和控制原理,給出了通用計算機鍵盤在單片機中的串行接口,采用該技術可大大增強單片機的漢字輸入功能。為小容量ROM單片機的大批量漢字信息處理提供了一種漢字輸入解決方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上傳時間: 2013-11-19
上傳用戶:jhksyghr
為解決傳統可視倒車?yán)走_(dá)視頻字符疊加器結構復雜,可靠性差,成本高昂等問題,在可視倒車?yán)走_(dá)設計中采用視頻字符發生器芯片MAX7456。該芯片集成了所有用于產生用戶定義OSD,并將其插入視頻信號中所需的全部功能,僅需少量的外圍阻容元件即可正常工作。給出了以MAX7456為核心的可視倒車?yán)走_(dá)的軟、硬件實現方案及設計實例。該方案具有電路結構簡單、價格低廉、符合人體視覺習慣的特點。經實際裝車測試,按該方案設計的可視倒車?yán)走_(dá)視場清晰、提示字符醒目、工作可靠,可有效降低駕駛員倒車時的工作強度、減少倒車事故的發生。 Abstract: A new video and text generation chip,MAX7456,was used in the design of video parking sensor in order to simplify system structure,improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure,lower cost,and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and reliable performance,which makes the driver easy to see backward and reduces chance of accidents.
標簽: 7456 MAX 可視倒車 中的應用
上傳時間: 2013-12-10
上傳用戶:qiaoyue
針對船舶氣象儀保障維修而設計的船舶氣象儀測試系統,包括信息處理終端、主儀器檢測模塊、傳感器檢測模塊,各個模塊都采用基于AVR單片機的嵌入式系統,模塊之間通過CAN總線進行通信。結果表明,船舶氣象儀測試系統能夠快速檢測船舶氣象儀故障,與單純依靠人工方式排查故障相比,故障檢測時間縮短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments,which composed of information processing terminal, testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
標簽: AVR 單片機 氣象儀 測試系統
上傳時間: 2013-11-23
上傳用戶:stvnash
蟲蟲下載站版權所有 京ICP備2021023401號-1