Luminary Micro provides an analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
標簽： Oversampling Techniques ADC fo
上傳時間： 2013-12-17
上傳用戶：zhyiroy
Luminary Micro Stellaris™ microcontrollers that are equipped with an analog-to-digital converter(ADC), use an innovative sequence-based sampling architecture designed to be extremely flexible,yet easy to use. This application note describes the sampling architecture of the ADC. Sinceprogrammers can configure Stellaris microcontrollers either through the powerful StellarisFamilyDriver Library or through direct writes to the device's control registers, this application note describesboth methods. The information presented in this document is intended to complement the ADCchapter of the device datasheet, and assumes the reader has a basic understanding of howADCsfunction.
標簽： Microcontr Stellaris Using the
上傳時間： 2013-10-14
上傳用戶：blans
本文依據集成電路設計方法學，探討了一種基于標準Intel 8086 微處理器的單芯片計算機平臺的架構。研究了其與SDRAM，8255 并行接口等外圍IP 的集成，并在對AMBA協議和8086 CPU分析的基礎上，采用遵從AMBA傳輸協議的系統總線代替傳統的8086 CPU三總線結構，搭建了基于8086 IP 軟核的單芯片計算機系統，并實現了FPGA 功能演示。關鍵詞：微處理器； SoC；單芯片計算機；AMBA 協議 Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
上傳時間： 2013-12-27
上傳用戶：kernor
基于單DSP的VoIP模擬電話適配器研究與實現:提出和實現了一種新穎的基于單個通用數字信號處理器(DSP)的VoIP模擬電話適配器方案。DSP的I/O和存儲資源非常有限，通常適于運算密集型應用，不適宜控制密集型應用[5]。該系統高效利用單DSP的I/O和片內外存儲器資源，采用μC/OS-II嵌入式實時操作系統，支持SIP和TCP-UDP/IP協議，通過LAN或者寬帶接入，使普通電話機成為Internet終端，實現IP電話。該系統軟硬件結構緊湊高效，運行穩定，成本低，具有廣闊的應用前景。關鍵詞：模擬電話適配器；IP電話；數字信號處理器；μC/OS-II 【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II Research and Implementation of VoIPATA Based on Single DSP
上傳時間： 2013-11-20
上傳用戶：Wwill
基于LabVIEW和單片機的空調溫度場測量系統的研究:室內溫度是空調系統舒適性的重要指標,對其及時、準確地測量顯得非常重要。介紹單片機AT89C51 和數字式、單總線型溫度傳感器DS18B20 組成矩形測量網絡采集空調室內40 點溫度,LabVIEW作為開發平臺,二者之間通過串口實現數據通信,利用LabVIEW強大的數據處理和顯示功能對采集的空調溫度場數據進行實時處理、分析和顯示,詳細介紹了系統的硬件結構和軟件模塊的設計方案。關鍵詞:單片機;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上傳時間： 2014-05-05
上傳用戶：KSLYZ
基于PIC單片機的低功耗讀卡器硬件設計:本文提出了一個完整的基于串口的智能讀卡器子系統設計方案并將其實現。讀卡器的設計突出了小型化的要求，全部器件使用貼片封裝。為了減小讀卡器的體積，設計中還使用了串口竊電的技術，使用串口信號線直接給讀卡器供電。為此，讀卡器使用了省電的設計，采用了省電的集成電路，并大膽簡化了許多傳統的設計電路。關鍵字： 讀卡器， 單片機， 串口竊電 Abstract： This paper aims to put forward a complete design of Smart IC card reader based onSerial Port and propose the way of realizing it for the purpose of Network Security. SMD isadopted to make Smart IC reader smaller in this design. To reduce the volume of Smart ICreader， Serial Port powered technology is employed to get power from the signal line of Serial Port. For this reason， low-power consumption components are adopted in the design and some traditional designs are simplified to reduce the power consumption.Keywords： Card Reader； Single-chip Computer； Serial Port Powered IC 卡系統保存了加密算法所需要的工作密鑰，供加密算法對網絡上傳輸的數據加密使用，是整個系統網絡安全的核心。在IC 卡子系統中，讀卡器是一個重要的部分。它起著管理IC卡、在IC 卡和PC或網絡計算機間傳遞數據的重要作用。本文以一片PIC單片機為核心完成了基于RS232 串口的讀卡器的硬件設計。
上傳時間： 2014-04-14
上傳用戶：wanghui2438
一種實用的微機自動配料秤系統:介紹一種由單片機構成的配料秤。敘述了秤的傳感器、變送器、信號的變換、硬件原理、軟件流程以及和DCS 系統構成的單回路調節系統,此系統可廣泛地應用于各行業的配料控制中。關鍵詞:配料秤 單片機 單回路調節系統 DCS 系統 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上傳時間： 2013-10-12
上傳用戶：zwei41
基于單片機控制的二氧化碳濃度測試計:基于CDM4161二氧化碳氣體濃度測試模塊以及ATtiny26單片機,提出了一種二氧化碳濃度測試計的設計方案。該方案具有硬件電路簡單、成本低、可靠性高、測量準確等優點，具有較高的實用價值。 Abstract: Abstract：A desigh scheme of CO2 concentration meter based on CDM4161carbon dioxide concentration test module and ATtiny26micro-controller is presented in this paper.The design scheme features simple hardware circuit,low-cost,high reli-ability，accurate measurement and it has a high practical value.
上傳時間： 2013-11-14
上傳用戶：zjwangyichao
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
標簽： synchronous Emulating serial
上傳時間： 2014-01-31
上傳用戶：z1191176801
基于P87 C591的CAN總線系統智能節點設計Design of CAN System Intelligent Node Based on P87C591 給出了基于帶CAN控制器的單片8位微控制器P87C591的智能節點的硬件電路及軟件結構，詳細介紹了設計中的難點及實現過程中應注意的問題。關鍵詞:CAN總線;智能節點 Abstract:A h ardc ircuita nds oftw arec onfigurationo fth ei ntelligentnode based on a microcontroller with CAN controller P87C591 arepresented.E speciallyt hec ruxi nd esigninga ndt hep roblemst hatshould be paid attention in realizing are discussed in details.Keyw ords:C AN;in telligentn ode CA N 總線 是德國Bosch從20世紀80年代初為解決現代汽車中眾多的控制與測試儀器之間的數據交換而開發的一種串行數據通信協議，它是一種多主總線，通信介質可以是雙絞線、同軸電纜或光導纖維。由于CAN總線具有較強的糾錯能力，支持差分收發，因而適合高噪聲環境。并具有較遠的傳輸距離，適用于許多領域的分布式測控系統。目前已在工業自動化、建筑物環境控制、醫療設備等許多領域得到廣泛的應用。CAN已成為國際標準化組織IS011898標準。
上傳時間： 2013-10-30
上傳用戶：xymbian
