高壓雙管反激變換器的設計:介紹一種雙管反激的電路拓撲，分析了其工作原理，給出了一些關鍵技術參數的計算公式，設計并研制成功的30W 380V AC5 0H z/510V DC/+15.1 V DC(1A )、+5.2VDC(2A)輔助開關電源具有功率密度高、變換效率高、可靠性高等優良的綜合性能。該變換器在高電壓輸人情況下有重要的應用價值?！娟P 鍵 詞 】變換器，輔助開關電源，雙管反激 [Abstract】 A n e wt opologyfo rd oubles witchfl ybackc onverteris in troduced.Th eo perationp rincipleis a nalyzeda nds ome for mulas for calculating key parameters for the topology are presented. The designed and produced auxiliary switching power supply,i. e. 30W 380V AC5 0H z/5 10V DC/+15.1 V DC《1A )、+5.2 V DC《2A )，hase xcellentc omprehensivep erformances sucha sh ighp owerd ensity, hi ghc onversione fficiencya ndh ighr eliability.Th isc onverterh asim portanta pplicationv aluef orh igh input voltag [Keywords ]converter,au xiliary switchingp owers upply,do ubles witchf lybac
上傳時間： 2013-11-01
上傳用戶：Ants
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上傳時間： 2013-10-27
上傳用戶：zhangyigenius
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上傳時間： 2013-10-23
上傳用戶：copu
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上傳時間： 2014-01-06
上傳用戶：氣溫達上千萬的
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上傳時間： 2014-04-02
上傳用戶：han_zh
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上傳時間： 2014-01-24
上傳用戶：zl5712176
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上傳時間： 2013-10-21
上傳用戶：xiaozhiqban
CAN與RS232轉換節點的設計與實現 介紹將CAN總線接口與RS232總線接口相互轉換的設計方法和2種總線電平轉換關系，實現CAN總線與各模塊的接口設計，制定了相應的軟硬件設計方案，并給出軟件設計流程圖以及部分硬件設計原理圖。為CAN總線與RS232總線互聯提供了一種方法，對CAN總線與RS232總線接口設備的互聯和廣泛應用的實現具有重要意義。關鍵詞：CAN總線；RS-232總線；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
上傳時間： 2013-11-04
上傳用戶：leesuper
針對使用硬件描述語言進行設計存在的問題，提出一種基于FPGA并采用DSP Builder作為設計工具的數字信號處理器設計方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ設計流程，設計了一個12階FIR 低通數字濾波器，通過Quartus 時序仿真及嵌入式邏輯分析儀SignalTapⅡ硬件測試對設計進行了驗證。結果表明，所設計的FIR 濾波器功能正確，性能良好。 Abstract: Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as designed tool is pointed out.A 12-order low-pass FIR digital filter was designed according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the designed filter is correct in function and good in performance.
上傳時間： 2013-11-17
上傳用戶：lo25643
設計一種應用于某全地形ATV車載武器裝置中的中控系統，該系統設計是以TMS320F2812型DSP為核心，采用模塊化設計思想，對其硬件部分進行系統設計，能夠完成對武器裝置高低、回轉方向的運動控制，實現靜止或行進狀態中對目標物的測距，自動瞄準以及按既定發射模式發射彈丸和各項安全性能檢測等功能。通過編制相應的軟件，對其進行系統調試，驗證了該設計運行穩定。 Abstract: A central control system applied to an ATV vehicle weapons is designed. The system design is based on TMS320F2812 DSP as the core， uses modular design for its hardware parts. The central control system can complete the motion control of the level of weapons and equipment， rotation direction， to achieve a state of static or moving objects on the target ranging， auto-targeting and according to the established target and the projectile and the launch of the security performance testing and other functions. Through the development of appropriate software and to carry out system testing to verify the stability of this design and operation.
上傳時間： 2013-11-02
上傳用戶：jshailingzzh
