對某四輪獨立驅動電動汽車輪轂電機進行研究,設計一種永磁無刷直流電機控制器.以STM32F103RBT6芯片為基礎,對電機驅動電路、采樣電路和保護電路分別進行硬件設計與分析;同時,采用模塊化軟件設計方案,對該控制器的軟件系統進行升級.實驗驗證表明:所設計的電機控制器能使電機響應迅速、轉速穩定、無超調,且電動車動力輸出性能良好.A permanent magnet brushless direct current motor controller was designed by studying the hub motor of a four-wheel independent drive electric vehicle.Based on STM32 F103RBT6 chip,the hardware design and analysis of motor drive circuit,sampling circuit and protection circuit were carried out respectively.At the same time,modular software design scheme was adopted to upgrade the software system of the controller.Experimental results show that the designed motor controller can ensure the motor fast response,stable speed,no overshoot,and good power output performances.
上傳時間： 2022-03-26
上傳用戶：qingfengchizhu
本系統采用電動機電樞供電回路串接采樣電阻的方式來實現對小型直流有刷電動機的轉速測量。該系統主要由二階低通濾波電路,小信號放大電路、單片機測量顯示電路、開關穩壓電源電路等組成。同時自制電機測速裝置,用高頻磁環作為載體,用線圈繞制磁環,利用電磁感應原理檢測電機運行時的漏磁,將變化的磁場信號轉化為磁環上的感應電流。用信號處理單元電路將微弱電信號轉化為脈沖信號,送由單片機檢測,從而達到準確測量電機的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
標簽： 直流電動機
上傳時間： 2022-03-26
上傳用戶：
基于藥物治療在臨床治療中的重要性,分析目前服藥提醒裝置存在的不足,以STM32F103VET6單片機為控制核心,設計了一種多功能電子藥箱。該系統包括顯示模塊、語音模塊和數據存儲模塊。顯示模塊通過觸摸屏電路和LED指示燈電路,與語音模塊相配合,實現了服藥提醒及指導的功能;數據存儲模塊通過EEPROM存儲電路,能夠實現掉電時服藥信息不丟失的功能。并且為了實現電子藥箱的智能化控制,開發了手機APP,兩者之間可通過WIFI進行數據通信。經測試,該藥箱能夠有效地幫助慢性病患者按時、定量、正確服用藥物,適合在家庭中推廣使用,具有較高的應用價值和實踐意義。Based on the importance of drug therapy in clinical treatment, this paper analyzes the shortcomings of current drug reminder devices, and designs a multi-function electronic medicine box with STM32 F103 VET6 microcontroller as the control core. The system includes a display module, a voice module, and a data storage module. The display module cooperates with the voice module through the touch screen circuit and the LED indicator circuit to realize the function of reminding and guiding the medicine;the data storage module can realize the function of not losing the medication information when the power is off through the EEPROM storage circuit.After testing, the medicine box can effectively help chronic diseases patients to take drugs on time, in a quantitative and correct manner,and is suitable for popularization in the family, and has high application value and practical significance.
標簽： 電子藥箱
上傳時間： 2022-03-27
上傳用戶：
配電網中,各種配電終端的電流、電壓、有功功率及無功功率等模擬量的采集是配電網自動化的重要環節。這些模擬量的采集也是各種儀器和家用電器的必要功能。因此,設計了基于嵌入式STM32F103單片機的交流電壓、交流電流及有功功率的采集系統,通過電壓互感器TV1005M和電流互感器TA1005M分別檢測交流電壓和交流電流值;屏幕或者手機APP和WiFi模塊互聯后,可以實時顯示交流電壓、交流電流、功率及電量值;通過設定閾值功率,可以實現對電流的監控和對電路的保護。In the distribution network,the collection of analog,such as current,voltage,active power,and reactive power at various distribution terminals is a very important part of distribution network automation. These analog acquisitions are also for various instruments and household appliances. Very important technology. Therefore,an AC voltage,AC current and active power acquisition system based on embedded STM32 F103 machine is designed,and AC voltage and AC current values are detected by voltage transformer TV1005 M and current Transformer TA1005 M respectively;After the screen or mobile phone APP and WiFi modules are interconnected,AC voltage,AC current,power,and power values can be displayed in real time;By setting the threshold power,the current can be monitored and the circuit can be protected.
上傳時間： 2022-03-27
上傳用戶：shjgzh
本系統基于STM32單片機設計的非接觸式電流檢測控制系統,通過OPA548片將所給任意信號放大,由100Ω電阻和INA128芯片進行電流電壓轉換放大后,利用STM32單片機對獲取的電壓信號以0.488μs頻率采樣,利用STM32單片機的FFT庫,獲得信號的諧波信息。測量電流信號精準,該設計可廣泛應用在以STM32單片機為核心控制器件的新型儀表中,性能精準且抗干擾能力強。This system is a non-contact current detection and control system based on STM32 single chip microcomputer. It amplifiesany signal through OPA548 chip, converts and amplifies the current and voltage by 100 Ω resistance and INA128 chip. The obtainedvoltage signal is sampled at the frequency of 0.488 μs by STM 32 single chip microcomputer, and the harmonic information of the signalis obtained by the FFT library of STM 32 single chip microcomputer. The measurement of current signal is accurate. This design can bewidely used in a new instrument with STM 32 single chip microcomputer as its core control device, with accurate performance and stronganti-interference capability.
上傳時間： 2022-03-27
上傳用戶：
設計功率MOSFET驅動電路時需重點考慮寄生參數對電路的影響。米勒電容作為MOSFET器件的一項重要參數,在驅動電路的設計時需要重點關注。重點觀察了MOSFET的開通和關斷過程中柵極電壓、漏源極電壓和漏源極電流的變化過程,并分析了米勒電容、寄生電感等寄生參數對漏源極電壓和漏源極電流的影響。分析了柵極電壓在米勒平臺附近產生振蕩的原因,并提出了抑制措施,對功率MOSFET的驅動設計具有一定的指導意義。When designing the drive circuit of power MOSFET,the influence of parasitic parameters on the circuit should be concerned.As an important parameter of MOSFET device,Miller capacitance should be considered in the design of drive circuit.The variation of gate voltage,drain source voltage and drain source current during the turn-on and turn-off of MOSFET were observed.The influences of parasitic parameters such as Miller capacitance and parasitic inductance on drain source voltage and drain source current were analyzed.The reasons of gate voltage oscillation nearby Miller plateau were analyzed,and the restraining measures were put forward.This research was instructive for the drive design of power MOSFET.
標簽： mosfet
上傳時間： 2022-04-02
上傳用戶：默默
鋰電池BMS管理技術是移動機器人的關鍵技術,本文設計了基于bq76PL455、STM32F103的鋰電池管理系統,實現了電池組電壓、電流、過壓、過流等狀態監測;系統配置均衡電路,電池充電過程中若出現電池單體電壓不平衡現象,會觸發均衡電路,進而提高電池的安全性,延長使用壽命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is proposed to realize the monitoring of battery pack voltage,current,overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
上傳時間： 2022-04-02
上傳用戶：
通過采用無橋PFC和半橋LLC諧振變換器作為數字開關電源的主變換拓撲,基于STM32系列微控制器的全數字控制PFC和DC-DC變換器,首先對數字化開關電源方案進行對比,然后闡述了200W數字開關電源整體方案,并對數字開關電源的無橋PFC和半橋LLC變換器進行系統研究。By using a bridgeless PFC and a half-bridge LLC resonant converter as the main conversion topology of the digital switching power supply,the all-digital control PFC and DC-DC converter based on the STM32 series of microcontrollers,firstly the digital switching power supply scheme is compared,and then the overall scheme of 200 W digital switching power supply is expounded, and the bridgeless PFC and half-bridge LLC converter of digital switching power supply are systematically studied.
標簽： 數字開關電源
上傳時間： 2022-04-02
上傳用戶：qingfengchizhu
電學中的測量技術涉及范圍非常廣,電流測量在電學計量中占有非常重要的位置。如何精確地進行電流測量是精密測量的一大難題。傳統的電流檢測電路多采用運算放大芯片與片外電流檢測電路相結合的方式,電路集成度很低,需要較多的接口和資源才能完成對電路的檢測。本文把所有電路部分都集成在一塊芯片上,包括檢測電阻,運算放大器電路及模擬轉數字轉換電路,從而在電路內部可以進行電流檢測,使電路更好的集成化。前置電路使用二級共源共柵結構的運算放大器,減小溝道長度調制效應造成的電流誤差。10位SAR ADC中采用電容驅動能力強的傳輸門保證了模數轉化器的有效精度。比較器模塊采用再生鎖存器與遲滯比較器作為基礎單元組合解決精密測量的問題。本設計可以作為嵌入芯片內的一小部分而檢測芯片中的微小電流1mA~100mA,工作電壓在1.8v左右,電流檢測精度預期達到10uA的需求。The measurement technology in electricity involves a wide range,and current measurement plays a very important position in electrical measurement.How to accurately measure current is a big problem in precision measurement. The traditional current detecting circuit adopts the combination of the operational amplifier chip and theoff-chip current detecting circuit, The circuit integration is very low, and more interfaces and resources are needed tocomplete the circuit detection.This topic integrates all the circuit parts into one chip, including detection resistance, operational amplifier circuit andanalog to digital conversion circuit. Highly integrated circuit makes the external resources on the chip more intensive,so that current detection can be carried out inside the circuit, so that the circuit can be better integrated. Thefront-end circuit of this project uses two-stage cascade operational amplifier and cascade tube to reduce the currenterror caused by channel length modulation effect. In 10-bit SAR ADC, the transmission gate with strong capacitivedriving ability ensures the effective accuracy of the analog-to-digital converter. Comparator module uses regenerativelatch and hysteresis comparator as basic unit to solve the difficult problem of precision measurement. This topic can beused as a small part of the embedded chip to detect the micro-current in the chip 1 mA~100 mA, the working voltageis about 1.8v, and the current detection accuracy is expected to reach the requirement of 10 uA.
上傳時間： 2022-04-03
上傳用戶：
隨著電磁閥在工業和日常應用的增多,其功耗越來越被人們所重視。通過對電磁閥驅動電路的研究,設計一套電磁閥節能驅動電路。不僅提高了電磁閥的響應時間,更重要的是降低了功耗,使電磁閥由工作在大電流狀態下,變成大電流啟動小電流維持的工作狀態。減少了由電流過大引起的電磁閥線圈過熱,增加了電磁閥的安全性。The power consumption of an electromagnetic valve is drawing increasingly more attentiori as it is widely used in industrial production and daily life. In this study, an energy - saving driving circuit of electromagnetic valves was designed. It can make an electromagnetic valve to start with a high current while work with a low current; thereby the power consumption can be reduced. Besides, it can shorten the response time of an electromagnetic valve and improve the security of the valve.
上傳時間： 2022-04-16
上傳用戶：
