Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
標簽： Converters Defini DAC
上傳時間： 2013-10-30
上傳用戶：stvnash
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上傳時間： 2013-11-12
上傳用戶：pans0ul
cv181l-a-20
標簽： Specification_V 181 1.0 L-A
上傳時間： 2013-11-14
上傳用戶：daijun20803
PCB LAYOUT 基本規範項次 項目 備註1 一般PCB 過板方向定義： PCB 在SMT 生產方向為短邊過迴焊爐(Reflow), PCB 長邊為SMT 輸送帶夾持邊. PCB 在DIP 生產方向為I/O Port 朝前過波焊爐(Wave Solder), PCB 與I/O 垂直的兩邊為DIP 輸送帶夾持邊.1.1 金手指過板方向定義： SMT: 金手指邊與SMT 輸送帶夾持邊垂直. DIP: 金手指邊與DIP 輸送帶夾持邊一致.2 SMD 零件文字框外緣距SMT 輸送帶夾持邊L1 需≧150 mil. SMD 及DIP 零件文字框外緣距板邊L2 需≧100 mil.3 PCB I/O port 板邊的螺絲孔(精靈孔)PAD 至PCB 板邊, 不得有SMD 或DIP 零件(如右圖黃色區).PAD
上傳時間： 2014-12-24
上傳用戶：jokey075
半導體的產品很多，應用的場合非常廣泛，圖一是常見的幾種半導體元件外型。半導體元件一般是以接腳形式或外型來劃分類別，圖一中不同類別的英文縮寫名稱原文為 PDID：Plastic Dual Inline Package SOP：Small Outline Package SOJ：Small Outline J-Lead Package PLCC：Plastic Leaded Chip Carrier QFP：Quad Flat Package PGA：Pin Grid Array BGA：Ball Grid Array 雖然半導體元件的外型種類很多，在電路板上常用的組裝方式有二種，一種是插入電路板的銲孔或腳座，如PDIP、PGA，另一種是貼附在電路板表面的銲墊上，如SOP、SOJ、PLCC、QFP、BGA。 從半導體元件的外觀，只看到從包覆的膠體或陶瓷中伸出的接腳，而半導體元件真正的的核心，是包覆在膠體或陶瓷內一片非常小的晶片，透過伸出的接腳與外部做資訊傳輸。圖二是一片EPROM元件，從上方的玻璃窗可看到內部的晶片，圖三是以顯微鏡將內部的晶片放大，可以看到晶片以多條銲線連接四周的接腳，這些接腳向外延伸並穿出膠體，成為晶片與外界通訊的道路。請注意圖三中有一條銲線從中斷裂，那是使用不當引發過電流而燒毀，致使晶片失去功能，這也是一般晶片遭到損毀而失效的原因之一。 圖四是常見的LED，也就是發光二極體，其內部也是一顆晶片，圖五是以顯微鏡正視LED的頂端，可從透明的膠體中隱約的看到一片方型的晶片及一條金色的銲線，若以LED二支接腳的極性來做分別，晶片是貼附在負極的腳上，經由銲線連接正極的腳。當LED通過正向電流時，晶片會發光而使LED發亮，如圖六所示。 半導體元件的製作分成兩段的製造程序，前一段是先製造元件的核心─晶片，稱為晶圓製造；後一段是將晶中片加以封裝成最後產品，稱為IC封裝製程，又可細分成晶圓切割、黏晶、銲線、封膠、印字、剪切成型等加工步驟，在本章節中將簡介這兩段的製造程序。
上傳時間： 2014-01-20
上傳用戶：蒼山觀海
為了實現直流電源的監控，提出了一種具有USB HID數據通信功能的直流電源設計方案。詳細論述了基于STM32 USB固件庫（USB-FS Device library V3.3）的自定義HID類下位機的實現，介紹了如何在VC2010集成開發環境中編寫多線程上位機程序并運用PlotLab（一個快速信號繪圖和可視化的VCL組件）顯示實時波形，最后再以實驗開發板和PC實現了HID數據通信，證明了此監控設計方案的可行性。
上傳時間： 2013-10-17
上傳用戶：13162218709
USB充電自動識別芯片，支持Apple手機，電流可達2A。
上傳時間： 2013-11-25
上傳用戶：dancnc
德州儀器微小型電源電路顯著簡化USB電池充電器設計
上傳時間： 2014-12-24
上傳用戶：浩子GG
2012TI杯陜西賽題H題,2012TI杯陜西賽題-A微弱信號檢測裝置.
上傳時間： 2013-12-17
上傳用戶：362279997
2011全國大賽A題開關電源模塊并聯供電系統
上傳時間： 2013-11-10
上傳用戶：冇尾飛鉈
