<input id="assey"></input>
<pre id="assey"></pre> 基于ARM11的嵌入式視頻處理終端設計 在研究了基于ARMl 1體系結構的Samsung$3C6410處理器的基 礎上，給出了多格式視頻編解碼的使用方法和Windows CE下中斷流 驅動的設計方法，為Windows CE操作系統下的圖像采集和視頻處理 的復雜控制提供了軟件實現的方法；并以該處理器為核心，加上外部 存儲器和USB攝像頭等接口電路，完成了一個嵌入式視頻處理終端 核心板的硬件原理圖設計和PCB圖的設計，并對視頻處理終端的印 制電路板的電磁兼容進行了研究。 首先對嵌入式系統和視頻處理進行了簡單的介紹，指出了采用 $3C6410處理器設計的視頻處理終端具有的優勢。其次，對$3C6410 多格式視頻編解碼的使用進行了仔細分析，為多格式視頻編解碼軟件 的編寫提供了思路。給出了Windows CE下中斷流驅動程序的設計方 法，為主處理器和BIT處理器在Windows CE下中斷流驅動的設計提 供了一種較為通用的參考模型。第三，在熟悉了S3C64lO處理器的 體系結構基礎上設計出了下列電路原理圖：電源及復位電路，時鐘電 路，DDR SDRAM和FLASH存儲器電路，USB接口電路，串口電路， JTAG接口電路，LCD和TSP接口電路。整個嵌入式視頻處理終端是 一個可以獨立工作的可擴展系統，該系統主要用于圖像采集和視頻編 解碼功能。另外，分別從濾波和接地等電磁兼容性設計手段出發，對 這些方法進行了理論分析，提出了提高視頻處理終端電磁兼容的措 施。最后，通過編寫簡單的應用程序，視頻處理終端對圖像進行H．264 編碼，可以通過無線網卡進行傳輸編碼后的圖像。測試結果表明，視 頻處理終端能夠實現視頻圖像的拍攝、壓縮、無線視頻傳送和視頻監 控等功能。
上傳時間： 2013-11-22
上傳用戶：誰偷了我的麥兜
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上傳時間： 2013-10-24
上傳用戶：s藍莓汁
概要2 個對稱的600MHz 高性能Blackfin 內核328K Bytes 片內存儲器每個 Blackfin 內核包括:2 個16 位MAC，2 個40 位ALU，4 個8 位視頻ALU，以及1 個40 位移位器RISC 式寄存器和指令模型，編程簡單，編譯環境友好先進的調試、跟蹤和性能監視內核電壓 0.8V-1.2V，片內調壓器可調兼容 3.3V 及2.5V I/O256 引腳Mini-BGA 和297 引腳PBGA 兩種封裝外設兩個并行輸入/輸出外圍接口單元，支持ITU-R 656 視頻數據格式，可與ADI 的模擬前端ADC 無縫連接2 個雙通道全雙工同步串行接口，支持8 個立體聲I2S 通道2 個16 通道DMA 控制器和1 個內部存儲器DMA 控制器SPI 兼容端口12 個通用32-bit 定時/計數器，支持PWMSPI 兼容端口支持 IrDA 的UART2 個“看門狗”定時器48 個可編程標志引腳1x-63x 倍頻的片內PLL
上傳時間： 2013-11-06
上傳用戶：YUANQINHUI
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上傳時間： 2014-12-30
上傳用戶：aysyzxzm
Abstract: With industrial/scientific/medical (ISM) band radio frequency (RF) products, often times users are new to the structure of Maxim's low pin-count transmitters andfully integrated superheterodyne receivers. This tutorial provides simple steps that can be taken to get the best performance out of these transmitters and receivers whileproviding techniques to measure the overall capability of the design.
上傳時間： 2013-11-02
上傳用戶：yph853211
Abstract: When people want portable music, they usually rely on battery-powered audio devices. With a bit of engineeringblood (or curiosity) running in your veins, it is not difficult to build a wireless Bluetooth® stereo audio system that can becontrolled with any device that has a Bluetooth connection and a music player
上傳時間： 2013-10-09
上傳用戶：天空說我在
Abstract: This application note illustrates the flexibility of the MAX7060 ASK/FSK transmitter. While the currently available evaluationkit (EV kit) has been optimized for the device's use in a specific frequency band (i.e., 288MHz to 390MHz), this document addresseshow the EV kit circuitry can be modified for improved operation at 433.92MHz, a frequency commonly used in Europe. Twoalternative match and filter configurations are presented: one for optimizing drain efficiency, the other for achieving higher transmitpower. Features and capabilities of earlier Maxim industrial, scientific, and medical radio-frequency (ISM-RF) transmitters areprovided, allowing comparison of the MAX7060 to its predecessors. Several design guidelines and cautions for using the MAX7060are discussed.
上傳時間： 2013-11-14
上傳用戶：swaylong
The NXP LPC314x combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, three channel10-bit A/D, and a myriad of serial and parallel interfaces in a single chip targeted atconsumer, industrial, medical, and communication markets. To optimize system powerconsumption, the LPC314x have multiple power domains and a very flexible ClockGeneration Unit (CGU) that provides dynamic clock gating and scaling.
上傳時間： 2013-10-11
上傳用戶：yuchunhai1990
本軟件是關于MAX338, MAX339的英文數據手冊：MAX338, MAX339 8通道/雙4通道、低泄漏、CMOS模擬多路復用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上傳時間： 2013-11-12
上傳用戶：18711024007
This example provides a description of how to use the USART with hardware flowcontrol and communicate with the Hyperterminal.First, the USART2 sends the TxBuffer to the hyperterminal and still waiting fora string from the hyperterminal that you must enter which must end by '\r'character (keypad ENTER button). Each byte received is retransmitted to theHyperterminal. The string that you have entered is stored in the RxBuffer array. The receivebuffer have a RxBufferSize bytes as maximum. The USART2 is configured as follow: - BaudRate = 115200 baud - Word Length = 8 Bits - One Stop Bit - No parity - Hardware flow control enabled (RTS and CTS signals) - Receive and transmit enabled - USART Clock disabled - USART CPOL: Clock is active low - USART CPHA: Data is captured on the second edge - USART LastBit: The clock pulse of the last data bit is not output to the SCLK pin
上傳時間： 2013-10-31
上傳用戶：yy_cn
