Abstract: The DS4830 optical microcontroller's analog-to-digital converter (ADC) offset can change with temperature and gainselection. However, the DS4830 allows users to measure the ADC internal offset. The measured ADC offset is added to the ADCoffset register to nullify the offset error. This application note demonstrates the DS4830's ADC internal offset calibration in theapplication program.
This unique guide to designing digital VLSI circuits takes a top-down approach, reflecting the natureof the design process in industry. Starting with architecture design, the book explains the why andhow of digital design, using the physics that designers need to know, and no more.Covering system and component aspects, design verification, VHDL modelling, clocking, signalintegrity, layout, electricaloverstress, field-programmable logic, economic issues, and more, thescope of the book is singularly comprehensive.
The LM20, LM45, LM50, LM60, LM61, and LM62 are analog output temperature sensors. They have various output voltage slopes (6.25mV/°C to 17mV/°C) and power supply voltage ranges (2.4V to 10V).The LM20 is the smallest, lowest power consumption analog output temperature sensor National Semiconductor has released. The LM70 and LM74 are MICROWIRE/SPI compatible digital temperature sensors. The LM70 has a resolution of 0.125°C while the LM74 has a resolution of 0.625°C. The LM74 is the most accurate of the two with an accuracy better than ±1.25°C. The LM75 is National’s first digital output temperature sensor, released several years ago.
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
•Founded in Jan. 08, 2001 in Shanghai, China.•Fabless IDH focused on Analog & Mixed Signal Chip design & marketing •Over 100 IC introduced.•Over 200 OEM Customer worldwide•ISO-9000 Certified•Distribution Channel in Taiwan, China & Japan
To achieve 100% customer satisfactionby producing the technically advanced product with the best quality, on-time delivery and service.
Leverages on proprietary process and world-class engineering team to develop innovative & high quality analog solutions that add value to electronics equipment.
設計了一種基于PIC16C71單片機的數字水溫配制閥。該配制閥采用NTC熱敏電阻作溫度傳感器，與固定電阻組成簡單分壓電路作為水溫測量電路，利用PIC16C71單片機內置的8位A/D轉換器把熱敏電阻上的模擬電壓轉換為數字量，PIC16C71單片機控制直流電機驅動混水閥調節冷熱水的混合比例實現水溫調節。給出了控制電路圖，對水溫測量電路的參數選擇和測溫精度作了詳細討論。實驗和分析表明，選用阻值較大的NTC熱敏電阻和分壓電阻可較好地解決熱敏電阻因功耗較大造成的熱擊穿問題。
Abstract:
A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
為提高電容測量精度，針對電容式傳感器的工作原理設計了基于PIC16LF874單片機電容測量模塊。簡單闡述了電容測量電路的應用背景和國內外研究現狀，介紹了美國Microchip公司PIC16LF874單片機的特性。電容式傳感器輸出的動態微弱電容信號通過PS021型電容數字轉換器把模擬量數據轉換成數字量數據，所測數據由PIC16LF874單片機應用程序進行處理、顯示和保存。實驗結果表明，固定電容標稱值為10~20 pF 的測量值相對誤差在1%以內，同時也可知被測電容容值越大，測量值和標稱值相對誤差越小。
Abstract:
To improve the accuracy of capacitance measurement，aimed at the principle of work of mercury capacitance acceleration transducer，the design of micro capacitance measurement circuit is based on the key PIC16LF874 chip. Briefly discusses the application of the capacitance measuring circuit for the background and status of foreign researchers，focusing on the United States PIC16LF874 microcontroller features. Capacitive sensor outputed signal through the dynamics of weak PS021-chip capacitors （capacitancedigital converter） to convert analog data into digital data，the measured data from the PIC16LF874 microcontroller application process， display and preservation. Experimental results show that the fixed capacitor 10pF ~ 20pF nominal value of the measured value of relative error is within 1%，but also it canbe seen the value of the measured capacitance larger，measuring value and the nominal value of relative error smaller.
詳細介紹了TLC1549系列模數轉換器的特點及工作原理，然后根據TLC1549的工作時序和A/D轉換原理針對實際問題編寫了詳細的匯編語言程序。
Abstract:
A basic principle and characteristic of TLC1549 analog-to-digital converter are introduced? detailedly in this article.Through engineering-oriented illustration,a microcomputer programmer base on basic principle and time sequence of TLC1549 is writted.
