在開放式數控系統結構模型的基礎上，研究了基于ISA總線的DSP通信控制原理。采用中斷方式完成了PC機和DSP之間的通信。介紹了以DriverWorks為工具開發ISA設備WDM驅動程序的方法，探討了中斷處理、驅動程序與應用程序之間的通信,簡要說明了驅動程序的安裝與調試。通過調試,系統設計運行穩定。 Abstract: The ISA bus and DSP correspondence control principle is investigated in the basis of the existing open architecture numerical control system.The interrupt method is used to realize the communication between PC and DSP based on the ISA bus.The methods of WDM driver exploitation for ISA device using Driver Works are introduced.The main process of driver program and the keys such as handle interrupt and the communication between the drivers and application are presented.And how to debug and install the drive is explained.
上傳時間： 2013-11-04
上傳用戶：kang1923
The CAT9555 is a CMOS device that provides 16-bitparallel input/output port expansion for I²C and SMBuscompatible applications. These I/O expanders providea simple solution in applications where additional I/Osare needed: sensors, power switches, LEDs,pushbuttons, and fans.
上傳時間： 2014-01-09
上傳用戶：1101055045
The CAT9534 is an 8-bit parallel input/output portexpander for I²C and SMBus compatible applications.These I/O expanders provide a simple solution inapplications where additional I/Os are needed: sensors,power switches, LEDs, pushbuttons, and fans.The CAT9534 consists of an input port register, anoutput port register, a configuration register, a polarityinversion register and an I²C/SMBus-compatible serialinterface.
上傳時間： 2013-11-09
上傳用戶：liulinshan2010
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上傳時間： 2013-11-23
上傳用戶：weixiao99
針對使用硬件描述語言進行設計存在的問題，提出一種基于FPGA并采用DSP Builder作為設計工具的數字信號處理器設計方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ設計流程，設計了一個12階FIR 低通數字濾波器，通過Quartus 時序仿真及嵌入式邏輯分析儀SignalTapⅡ硬件測試對設計進行了驗證。結果表明，所設計的FIR 濾波器功能正確，性能良好。 Abstract: Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as designed tool is pointed out.A 12-order low-pass FIR digital filter was designed according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the designed filter is correct in function and good in performance.
上傳時間： 2013-11-17
上傳用戶：lo25643
針對運行中火車測速運用多普勒效應采用DSP 設計雷達測速系統并闡述了其基本設計思想與工作原理給出系統硬件軟件設計結構和原理圖改善了原有光電測速精度提高了系統工作穩定性和可靠性經實驗證明DSP 采集板工作穩定測速效果好關鍵詞DSP; 雷達測速; 多普勒效應 On Board DSP-Based Radar Speed Measurement System TANG Wei, SUN Zhi-fang, CHEN Quan (Dept.of computer Science,Yangtze University,Jingzhou 434023,China)Abstract: This paper presents a DSP-based train speed measurement by using Doppler radar. The structure of the system is introduced.The hardware and software are also discussed.Key words: DSP; rader speed measurement; doppler principle
上傳時間： 2013-10-27
上傳用戶：003030
With the Altera Nios II embedded processor, you as the system designercan accelerate time-critical software algorithms by adding custominstructions to the Nios II processor instruction set. Using custominstructions, you can reduce a complex sequence of standard instructionsto a single instruction implemented in hardware. You can use this featurefor a variety of applications, for example, to optimize software innerloops for digital signal processing (DSP), packet header processing, andcomputation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphicaluser interface (GUI) used to add up to 256 custom instructions to theNios II processor
上傳時間： 2013-11-07
上傳用戶：swing
Nios II定制指令用戶指南：With the Altera Nios II embedded processor, you as the system designer can accelerate time-critical software algorithms by adding custom instructions to the Nios II processor instruction set. Using custom instructions, you can reduce a complex sequence of standard instructions to a single instruction implemented in hardware. You can use this feature for a variety of applications, for example, to optimize software inner loops for digital signal processing (DSP), packet header processing, and computation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphical user interface (GUI) used to add up to 256 custom instructions to the Nios II processor. The custom instruction logic connects directly to the Nios II arithmetic logic unit (ALU) as shown in Figure 1–1.
上傳時間： 2013-10-12
上傳用戶：kang1923
CGAL is a collaborative effort of several sites in Europe and Israel. The goal is to make the most important of the solutions and methods developed in computational geometry available to users in industry and academia in a C++ library. The goal is to provide easy access to useful, reliable geometric algorithms
標簽： collaborative several Europe Israel
上傳時間： 2015-01-09
上傳用戶：refent
Pocket 1945 is a classic shooter inspired by the classic 1942 game. The game is written in C# targeting the .NET Compact Framework. This article is my first submission to Code Project and is my contribution to ongoing .NET CF competition.
標簽： classic game inspired shooter
上傳時間： 2014-02-10
上傳用戶：康郎
