Abstract: The DS1875 features a pulse-width modulation (PWM) controller that can be used to control aDC-DC converter. The DC-DC converter can then be used to generate the high bias voltages necessaryfor avalanche photodiodes (APDs). This application note Describes the operation of a boost converterthat uses the DS1875. Discussion covers the selection of the inductor and switching frequency, and theselection of components that improve the efficiency of the converter. Test data are presented.
Abstract: Some types of loads require more current during startup than when running. Other loads can be limited to a lower-powercurrent during startup but require a higher operating current. This article Describes an application circuit that automatically adjusts apower circuit’s overcurrent protection level up or down after startup is complete.
光伏發電是未來新能源發電重要方向之一，而光伏變流器是光伏發電系統的核心。介紹一種基于微網理念的光伏變流器設計。以該變流器為核心的光伏發電系統可以看做一個小型的微網系統。該系統能根據外部電網情況，工作于并網模式和離網模式。介紹了該系統的各個組成部件的設計以及變流器主電路部分器件的選型。最后，由實驗樣機進行測試。試驗結果驗證了電路拓撲結構及控制方案的可行性，也說明了系統參數設計方法的正確性。
Abstract:
Solar Photovoltaic generation is an important direction of new energy power generation in the future，while photovoltaic converter is the core of photovoltaic generation system. This paper deals with a study on photovoltaic inverter based on the concept of microgrid. This paper Describes a system whose core component is the photovoltaic inverter，can work on grid-connected mode or run independently according to the external situation. The paper simply Describes the main components of the system. At last，the prototype was produced and tested. Test result has proved feasibility of circuit topology structure and controlling scheme and shown correctness of system parameters.Key words: PV inverter； microgrid； off-grid； storage battery
Abstract: This application note Describes how to build, debug, and run applications on the on-board MAXQ622microcontroller to interface with the DS8005 dual smart card interface. This is demonstrated in both IAREmbedded Workbench and the Rowley CrossWorks IDE, using sample code provided with the kit.
Analog Inputs and Outputs in an S7 PLC are represented in the PLC as a 16-bit integer. Over
the nominal span of the analog input or output, the value of this integer will range between -
27648 and +27648. However, it is easier to use the analog values if they are scaled to the
same units and ranges as the process being controlled. This applications tip Describes
methods for scaling analog values to and from engineering units.
Designing read/write device (RWD) units for industrial RF-Identification
applications is strongly facilitated by the NXP Semiconductors HITAG
Reader Chip HTRC110. All needed function blocks, like the antenna
driver, modulator demodulator and antenna diagnosis unit, are integrated
in the HTRC110. Therefore only a minimum number of additional passive
components are required for a complete RWD.
This Application Note Describes how to design an industrial
RF-Identification system with the HTRC110. The major focus is
dimensioning of the antenna, all other external components including
clock and power supply, as well as the demodulation principle and its
implementatio
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note Describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
針對科研實驗中對拉壓千斤頂加載過程控制的需要，采用ATmega128單片機控制步進電機進而實現對執行系統的電動泵站實行自動控制。對力和位移的數據采集與處理及用步進電機控制電動泵站手柄的技術細節作了重點描述。通過單片機的A/D變換器對AMP放大模塊采集的電橋信號作量化處理，千斤頂的操控手柄位置依電動油泵閥門開啟的方向和大小作若干定位，單片機根據力或位移傳感器信號，實時控制步進電機驅動手柄旋轉到相應操控位置。
Abstract:
This article Describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
AVR32801: UC3A3 Schematic Checklist Features • Power circuit • Reset circuit • USB connection • External bus interface • ABDAC sound DAC interface • JTAG and Nexus debug ports • Clocks and crystal oscillators • MMC, SD-card, SDHC, SDIO and CE-ATA interface 1 Introduction A good hardware design comes from a proper schematic. Since UC3A3 devices have a fair number of pins and functions, the schematic for these devices can be large and quite complex. This application note Describes a common checklist which should be used when starting and reviewing the schematics for a UC3A3 design.
設計一種基于ATmega16L單片機的溫度控制系統，闡述該系統的軟硬件設計方案。采用模塊化設計方法，利用增量式PID算法使被控對象的溫度值趨于給定值。實驗結果表明該系統具有良好的檢測和控制功能。 Abstract: This paper designs a temperature control system based on ATmega16L，Describes the hardware and software de－sign scheme of the system，adopts the modularized design method and utilizes the incremental PID algorithm to realize the temperature of controlled device incline to the given value.The experiment result indicates that the system has good detec－tion and control function
