以典型的9S08 系列為例，當你選擇了一個MCU 型號后，在圖1-4 右側會顯示出所有針對該型號芯片可用的項目調試場景。其中：Full Chip Simulator”是芯片全功能模擬仿真，即無需任何目標系統的硬件資源，直接在你的PC 機上模擬運行單片機的程序，在模擬運行過程中可以觀察調試程序的各項控制和運行流程，分析代碼運行的時間，觀察各種變量，等等。CW 提供了功能強大的模擬激勵功能，可以在模擬運行時模擬一些外部事件的輸入，配合程序調試；P&E Multilink/Cyclone Pro”是基于P&E 公司的硬件調試工具實現實時在線硬件調試。實際就是我們經常說的BDM 調試。BDM 調試是基于芯片本身內含的在線調試功能，可實現程序下載，單步／全速運行，可以設若干個斷點，可以觀察和修改任意寄存器或RAM 內存空間。BDM 幾乎是開發飛思卡爾8 位（9S08 和RS08 系列）、16 位（9S12 系列）和32 位（Coldfire V1 系列）單片機的標準調試模式，運用最為廣泛；SofTec HCS08”是另外一家SofTec 公司提供的硬件調試工具，國內使用較少；HCS08 Serial Monitor”是基于芯片串口的監控調試開發模式。由于開發效率較低，現在幾乎無人使用。
上傳時間： 2013-10-10
上傳用戶：alex wang
The Controller Area Network (CAN) is a serial, asynchronous, multi-master communication protocol forconnecting electronic control modules, sensors and actuators in automotive and industrial applications.With the SJA1000, Philips Semiconductors provides a stand-alone CAN controller which is more than a simpleeplacement of the PCA82C200.Attractive features are implemented for a wide range of applications, supporting system optimization, diagnosisand maintenance.
標簽： Stand-alone contro 1000 SJA
上傳時間： 2013-11-18
上傳用戶：yxgi5
The PCA82C250 and PCA82C251 are advanced transceiver products for use in automotive and general industrialapplications with transfer rates up to 1 Mbit/s. They support the differential bus signal representation beingdescribed in the international standard for in-vehicle CAN high-speed applications (ISO 11898). Controller AreaNetwork (CAN) is a serial bus protocol being primarily intended for transmission of control related data between anumber of bus nodes.
上傳時間： 2013-11-24
上傳用戶：Alick
The PCA9519 is a 4-channel level translating I2C-bus/SMBus repeater that enables theprocessor low voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBusmaximum capacitance of 400 pF on the higher voltage side. The SDA and SCL pins areover-voltage tolerant and are high-impedance when the PCA9519 is unpowered.
標簽： 4channel transla level 9519
上傳時間： 2013-11-19
上傳用戶：jisiwole
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
標簽： MULTICHANNEL 5.5 TO RS
上傳時間： 2013-10-19
上傳用戶：ddddddd
基于LabVIEW和單片機的空調溫度場測量系統的研究:室內溫度是空調系統舒適性的重要指標,對其及時、準確地測量顯得非常重要。介紹單片機AT89C51 和數字式、單總線型溫度傳感器DS18B20 組成矩形測量網絡采集空調室內40 點溫度,LabVIEW作為開發平臺,二者之間通過串口實現數據通信,利用LabVIEW強大的數據處理和顯示功能對采集的空調溫度場數據進行實時處理、分析和顯示,詳細介紹了系統的硬件結構和軟件模塊的設計方案。關鍵詞:單片機;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上傳時間： 2014-05-05
上傳用戶：KSLYZ
基于PIC單片機的低功耗讀卡器硬件設計:本文提出了一個完整的基于串口的智能讀卡器子系統設計方案并將其實現。讀卡器的設計突出了小型化的要求，全部器件使用貼片封裝。為了減小讀卡器的體積，設計中還使用了串口竊電的技術，使用串口信號線直接給讀卡器供電。為此，讀卡器使用了省電的設計，采用了省電的集成電路，并大膽簡化了許多傳統的設計電路。關鍵字： 讀卡器， 單片機， 串口竊電 Abstract： This paper aims to put forward a complete design of Smart IC card reader based onSerial Port and propose the way of realizing it for the purpose of Network Security. SMD isadopted to make Smart IC reader smaller in this design. To reduce the volume of Smart ICreader， Serial Port powered technology is employed to get power from the signal line of Serial Port. For this reason， low-power consumption components are adopted in the design and some traditional designs are simplified to reduce the power consumption.Keywords： Card Reader； Single-chip Computer； Serial Port Powered IC 卡系統保存了加密算法所需要的工作密鑰，供加密算法對網絡上傳輸的數據加密使用，是整個系統網絡安全的核心。在IC 卡子系統中，讀卡器是一個重要的部分。它起著管理IC卡、在IC 卡和PC或網絡計算機間傳遞數據的重要作用。本文以一片PIC單片機為核心完成了基于RS232 串口的讀卡器的硬件設計。
上傳時間： 2014-04-14
上傳用戶：wanghui2438
多功能高集成外圍器件6. 1 多功能高集成外圍器件82371PCI的英文名稱：Peripheral Component Interconnect （外圍部件互聯PCI總線）；82371是PCI總線組件。ISA是：Industry Standard Architecture（工業標準體系結構）IDE是 （Integrated Device Electronics）集成電路設備簡稱PIIX4PIIX4器件（芯片）的特點1、是一種支持Pentium和PentiumII微處理器的部件。2、82371對ISA橋來說，是一種多功能PCI總線。3、對可移動性和桌面深綠色環境均提供支持。4、電源管理邏輯。5、被集成化的IDE控制器。6、增強了性能的DMA控制器。 （7）基于兩個82C59的中斷控制器。（8）基于82C54芯片的定時器。（9）USB（Universal Serial Bus）通用串行總線。（10）SMBus系統管理總線。（11）實時時鐘（12）順應Microsoft Win95所需的功能其芯片的邏輯框圖如圖6-1所示。 PIIX4芯片邏輯框圖6.1.1 概述PIIX4芯片是一個多功能的PCI器件，圖6-2 是82371在系統中扮演的角色。（續上圖）1. PCI與EIO之間的橋（PIIX4芯片）橋是不對程的，是各類不同標準總線與PCI總線連接，82371AB橋也可理解為一種總線轉換譯碼器和控制器，橋內包含復雜的協議總線信號和緩沖器。(1).在PCI系統內，當PIIX4操作時，它總是作為系統內各種模塊的主控設備，如USB和DMA控制器、IDE總線和分布式DMA的主控設備等，而且總是以ISA主控設備的名義出現。(2). 在向ISA總線或IDE總線進行傳送操作的傳送周期期間作為從屬設備使用，并對內部寄存器譯碼。PIIX4芯片（橋）的配置(1).可以把PIIX4芯片配置成整個ISA總線，或ISA總線的子集，也可擴展成EIO總線。在使用EIO總線時，可以把未使用的信號配置成通用的輸入和輸出。(2).PIIX4可直接驅動5個ISA插槽；(3).能提供字節-交換邏輯、I/O的恢復支持、等待狀態的生成以及SYSCLK的生成。(4).提供X-BUS鍵盤控制器芯片、BIOS芯片、實時時鐘芯片、二級微程序器等的選擇。2. IDE接口（總線主控設備的權利和同步DMA方式）IDE接口為4個IDE的設備提供支持，比如IDE接口的硬盤和CD-ROM等。注意：目前硬盤接口有5類：IDE、SCSI、Fibre Channel、IEEE1394和USB等。IDE口幾乎在PC機最多，因為便宜。SCSI多用于服務器和集群機。IDE的PIO IDE速率：14MB/s；而總線主控設備IDE的速率：33MB/s在PIIX4芯片的IDE系統內，配有兩個各次獨立的IDE信號通道。3. 具有兼容性的模塊—DMA、定時器/計數器、中斷控制器等（1）在PIIX4內的兩各82C37 DMA控制器經邏輯的組合，產生7個獨立的可編程通道。通道[0：3]是通過與8個二進位的硬件連線實現的。通過以字節為單位的計數進行傳送。而通道[5：7]是通過16個二進位的連線實現的，以字為單位的計數進行傳送。（2）DMA控制器還能通過PCI總線，處理舊的DMA的兩個不同的方法提供支持。（3）計數/定時器模塊在功能上與82C54等價。（4）中斷控制器與ISA兼容，其功能是兩個82C59的功能之和。
上傳時間： 2013-11-19
上傳用戶：3到15
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB connection.
上傳時間： 2014-04-03
上傳用戶：lizhizheng88
