The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication protocol is defined for each serialinterface, with a compatible command set and sequences
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required.
The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
PROTEUS VSM在單片機系統仿真中的應用:：介紹了單片機系統仿真工具PROTEUS VSM 及其在單片機系統仿真中的應用，給出了具體的應用實例，詳細地介紹了PROTEUS VSM 與Keil uVision3的接口方法。關鍵詞：?jiǎn)纹瑱C(jī)；Keil uVision3；仿真；外圍器件；PROTEUS VSM；
Abstract：This paper introduces the simulation tool for M CU system —PROTEUS VSM ， and presents the application ofPROTEUS VSM in MCU system simulation through an applicable example．The way of interfacing PROTEUS VSM to Keil uVision3is also presented in details．Keywords：MCU ；Keil uVision3；simulation；peripheral devices；PROTEUS VSM ；
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
This application note describes how to decode standard DTMF tones using the minimum number of external discrete components and a PIC. The two examples use a PIC which has an 8 bit timer and either a comparator or an ADC, although it can be modified for use on a PIC which has only digital I/O. The Appendices have example code for the 16C662 (with comparator) and 16F877 (using the ADC).
As the majority of the Digital Signal Processing is done in software, little is required in the way of external signal conditioning. Software techniques are used to model the individual elements of a DTMF Decoder IC.
The PCA9516 is a BiCMOS integrated circuit intended forapplication in I2C and SMBus systems.While retaining all the operating modes and features of the I2Csystem, it permits extension of the I2C-bus by buffering both the data(SDA) and the clock (SCL) lines, thus enabling five buses of 400 pF.The I2C-bus capacitance limit of 400 pF restricts the number ofdevices and bus length. Using the PCA9516 enables the systemdesigner to divide the bus into five segments off of a hub where anysegment to segment transition sees only one repeater delay.
Luminary Micro provides an analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
