This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上傳時間： 2013-11-01
上傳用戶：wojiaohs
This application note explains the XC9500™/XL/XV Boundary Scan interface anddemonstrates the software available for programming and testing XC9500/XL/XV CPLDs. Anappendix summarizes the iMPACT software operations and provides an overview of theadditional operations supported by XC9500/XL/XV CPLDs for in-system programming.
上傳時間： 2013-11-01
上傳用戶：南國時代
Most designers wish to utilize as much of a device as possible in order to enhance the overallproduct performance, or extend a feature set. As a design grows, inevitably it will exceed thearchitectural limitations of the device. Exactly why a design does not fit can sometimes bedifficult to determine. Programmable logic devices can be configured in almost an infinitenumber of ways. The same design may fit when you use certain implementation switches, andfail to fit when using other switches. This application note attempts to clarify the CPLD softwareimplementation (CPLDFit) options, as well as discuss implementation tips in CoolRunnerTM-IIdesigns in order to maximize CPLD utilization.
上傳時間： 2014-01-11
上傳用戶：a471778
This application note provides a functional description of VHDL source code for a N x N DigitalCrosspoint Switch. The code is designed with eight inputs and eight outputs in order to targetthe 128-macrocell CoolRunner™-II CPLD device but can be easily expanded to target higherdensity devices. To obtain the VHDL source code described in this document, go to sectionVHDL Code, page 5 for instructions.
標簽： CoolRunner-II XAPP CPLD 380
上傳時間： 2013-10-26
上傳用戶：kiklkook
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
上傳時間： 2014-11-26
上傳用戶：erkuizhang
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上傳時間： 2013-11-23
上傳用戶：shen_dafa
XAPP520將符合2.5V和3.3V I/O標準的7系列FPGA高性能I/O Bank進行連接 The I/Os in Xilinx® 7 series FPGAs are classified as either high range (HR) or high performance (HP) banks. HR I/O banks can be operated from 1.2V to 3.3V, whereas HP I/O banks are optimized for operation between 1.2V and 1.8V. In circumstances that require an HP 1.8V I/O bank to interface with 2.5V or 3.3V logic, a range of options can be deployed. This application note describes methodologies for interfacing 7 series HP I/O banks with 2.5V and 3.3V systems
上傳時間： 2013-11-06
上傳用戶：wentianyou
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上傳時間： 2013-10-28
上傳用戶：jyycc
解壓密碼：www.elecfans.com 隨著微電子技術的迅速發展以及集成電路規模不斷提高，對電路性能的設計 要求越來越嚴格，這勢必對用于大規模集成電路設計的EDA 工具提出越來越高的 要求。自1972 年美國加利福尼亞大學柏克萊分校電機工程和計算機科學系開發 的用于集成電路性能分析的電路模擬程序SPICE（Simulation Program with IC Emphasis）誕生以來，為適應現代微電子工業的發展，各種用于集成電路設計的 電路模擬分析工具不斷涌現。HSPICE 是Meta-Software 公司為集成電路設計中 的穩態分析，瞬態分析和頻域分析等電路性能的模擬分析而開發的一個商業化通 用電路模擬程序，它在柏克萊的SPICE（1972 年推出），MicroSim公司的PSPICE （1984 年推出）以及其它電路分析軟件的基礎上，又加入了一些新的功能，經 過不斷的改進，目前已被許多公司、大學和研究開發機構廣泛應用。HSPICE 可 與許多主要的EDA 設計工具，諸如Candence,Workview 等兼容，能提供許多重要 的針對集成電路性能的電路仿真和設計結果。采用HSPICE 軟件可以在直流到高 于100MHz 的微波頻率范圍內對電路作精確的仿真、分析和優化。在實際應用中， HSPICE能提供關鍵性的電路模擬和設計方案，并且應用HSPICE進行電路模擬時， 其電路規模僅取決于用戶計算機的實際存儲器容量。 The HSPICE Integrator Program enables qualified EDA vendors to integrate their products with the de facto standard HSPICE simulator, HSPICE RF simulator, and WaveView Analyzer™. In addition, qualified HSPICE Integrator Program members have access to HSPICE integrator application programming interfaces (APIs). Collaboration between HSPICE Integrator Program members will enable customers to achieve more thorough design verification in a shorter period of time from the improvements offered by inter-company EDA design solutions.
上傳時間： 2013-10-18
上傳用戶：s363994250
Abstract: This application note presents an overview of electronic margining and its value in detectingpotential system failures before a product ships from the factory. It is a calibration method that effectivelypredicts and allows adjustments to improve product quality. Margining also can be used to sort productsinto performance levels, allowing premium products to be sold at premium prices. We discuss thedownside of sorting and suggest alternative ways to segregate products.
上傳時間： 2014-01-22
上傳用戶：lhw888
