Image enhancement in frequency domain using Fourier center frequency, Gaussian lowpass filter, Low pass filter, high pass filter. Image restoration using medean filter, weiner filter with noise generator such as Gaussian noise, Salt and Pepper noise
摘 要:用一種新的思路和方法,先計算低通、再計算高通濾波器的有關參數,然后組合成帶通濾波器.關鍵詞:濾波器;參數;新思路中圖分類號: TN713. 5 文獻識別碼:B 文章編號:1008 - 1666 (1999) 04 - 0089 - 03A New Consideration of the Band Filter’s CalculationGuo Wencheng( S hao Yang B usiness and Technology school , S haoyang , Hunan ,422000 )Abstract :This essay deals with a new method of calculating the band filters - first calculatingthe relevant parameters of low - pass filters ,then calculating the ones of high - pass filters.Key words :filter ; parameters ;new considercation八十年代后,信息產業得到了迅猛發展. 帶通濾波器在微波通信、廣播電視和精密儀器設備中得到了廣泛應用. 帶通濾波器性能的優劣,對提高接收機信噪比,防止鄰近信道干擾,提高設備的技術指標,有著十分重要的意義.我在長期的教學實踐中,用切比雪夫型方法設計、計算出寬帶濾波器集中參數元件的數據. 該濾波器可運用在檢測微波頻率的儀器和其他設備中. 再將其思路和計算方法介紹給大家,供參考.
針對使用硬件描述語言進行設計存在的問題，提出一種基于FPGA并采用DSP Builder作為設計工具的數字信號處理器設計方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ設計流程，設計了一個12階FIR 低通數字濾波器，通過Quartus 時序仿真及嵌入式邏輯分析儀SignalTapⅡ硬件測試對設計進行了驗證。結果表明，所設計的FIR 濾波器功能正確，性能良好。
Abstract:
Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as designed tool is pointed out.A 12-order Low-Pass FIR digital filter was designed according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the designed filter is correct in function and good in performance.
基于通用集成運算放大器，利用MASON公式設計了一個多功能二階通用濾波器，能同時或分別實現低通、高通和帶通濾波，也能設計成一個正交振蕩器。電路的極點頻率和品質因數能夠獨立、精確地調節。電路使用4個集成運放、2個電容和11個電阻，所有集成運放的反相端虛地。利用計算機仿真電路的通用濾波功能、極點頻率和品質因數的獨立控制和正交正弦振蕩，從而證明該濾波器正確有效。
Abstract:
A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， Low-Pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
he LPC932 can be used to create a Pulse Width Modulated PWM signal. That s an analog signal, with only 2 discrete levels, for example 0V and 5V and a constant period. The current value of this signal at a certain poiTnt of time is proportional to its Duty Cycle. That s the High Time during one period divided by the period. It can also be calculated as the average value during a particular period. That means after low pass filtering, (e.g. RC circuit) the signal becomes analog, with an actual value controlled by the microcontroller. The PWM functionality enables the LPC932 to control for example the speed of DC motors or the brightness of electric lighting.
This m file analyzes a coherent binary phase shift keyed(BPSK) and a amplitude shift keyed(ASK) communication system. The receiver uses a correlator(mixer-integrator[LPF]) configuration with BER measurements comparing measured and theoretical results. The bandpass and low pass used in the receiver are constructed using z transforms.
本系統采用電動機電樞供電回路串接采樣電阻的方式來實現對小型直流有刷電動機的轉速測量。該系統主要由二階低通濾波電路,小信號放大電路、單片機測量顯示電路、開關穩壓電源電路等組成。同時自制電機測速裝置,用高頻磁環作為載體,用線圈繞制磁環,利用電磁感應原理檢測電機運行時的漏磁,將變化的磁場信號轉化為磁環上的感應電流。用信號處理單元電路將微弱電信號轉化為脈沖信號,送由單片機檢測,從而達到準確測量電機的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order Low-Pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
The MAX2691 low-noise amplifier (LNA) is designed forGPS L2 applications. Designed in Maxim’s advancedSiGe process, the device achieves high gain andlow noise figure while maximizing the input-referred 1dBcompression point and the 3rd-order intercept point. TheMAX2691 provides a high gain of 17.5dB and sub 1dBnoise figure.
