以某高速實時頻譜儀為應用背景，論述了5 Gsps采樣率的高速數據采集系統的構成和設計要點，著重分析了采集系統的關鍵部分高速ADC（analog to digital，模數轉換器）的設計、系統采樣時鐘設計、模數混合信號完整性設計、電磁兼容性設計和基于總線和接口標準（PCI Express）的數據傳輸和處理軟件設計。在實現了系統硬件的基礎上，采用Xilinx公司ISE軟件的在線邏輯分析儀（ChipScope Pro）測試了ADC和采樣時鐘的性能，實測表明整體指標達到設計要求。給出上位機對采集數據進行處理的結果，表明系統實現了數據的實時采集存儲功能。
上傳時間： 2014-11-26
上傳用戶：黃蛋的蛋黃
Digital-to-analog converters (DACs) are prevalent inindustrial control and automated test applications.General-purpose automated test equipment often requiresmany channels of precisely controlled voltagesthat span several voltage ranges. The LTC2704 is ahighly integrated 16-bit, 4-channel DAC for high-endapplications. It has a wide range of features designed toincrease performance and simplify design.
上傳時間： 2013-11-22
上傳用戶：元宵漢堡包
Designers of signal receiver systems often need to performcascaded chain analysis of system performancefrom the antenna all the way to the ADC. Noise is a criticalparameter in the chain analysis because it limits theoverall sensitivity of the receiver. An application’s noiserequirement has a signifi cant infl uence on the systemtopology, since the choice of topology strives to optimizethe overall signal-to-noise ratio, dynamic range andseveral other parameters. One problem in noise calculationsis translating between the various units used by thecomponents in the chain: namely the RF, IF/baseband,and digital (ADC) sections of the circuit.
上傳時間： 2014-12-05
上傳用戶：cylnpy
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上傳時間： 2013-10-08
上傳用戶：wuyuying
The LM20, LM45, LM50, LM60, LM61, and LM62 are analog output temperature sensors. They have various output voltage slopes (6.25mV/°C to 17mV/°C) and power supply voltage ranges (2.4V to 10V).The LM20 is the smallest, lowest power consumption analog output temperature sensor National Semiconductor has released. The LM70 and LM74 are MICROWIRE/SPI compatible digital temperature sensors. The LM70 has a resolution of 0.125°C while the LM74 has a resolution of 0.625°C. The LM74 is the most accurate of the two with an accuracy better than ±1.25°C. The LM75 is National’s first digital output temperature sensor, released several years ago.
上傳時間： 2014-12-23
上傳用戶：yl8908
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a slope whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
標簽： Converters Defini DAC
上傳時間： 2013-10-30
上傳用戶：stvnash
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上傳時間： 2013-11-12
上傳用戶：pans0ul
前面討論了很多內容，基本上涉及了有關PCB板的絕大部分相關的知識。第二章探討了傳輸線的基本原理，第三章探討了串擾，在第四章里我們闡述了許多在現代設計中必須關注的非理想互連的問題。對于信號從驅動端引腳到接收端引腳的電氣路徑的相關問題，我們已經做了一些探究，然而對于硅芯片，即處于封裝內部的IC來說，其信號傳輸通常要通過過孔和連接器來進行，對這樣的情況我們該如何處理？在本章中，我們將通過對封裝、過孔和連接器的研究，闡述其原理，從而指導大家在設計的時候對整個電氣路徑進行完整地分析，即從驅動端內部IC芯片的焊盤到接受器IC芯片的焊盤。
標簽： High-Speed Digital System desi
上傳時間： 2013-11-24
上傳用戶：maizezhen
高速數字系統設計下載pdf:High-Speed Digital SystemDesign—A Handbook ofInterconnect Theory and DesignPracticesStephen H. HallGarrett W. HallJames A. McCallA Wiley-Interscience Publication JOHN WILEY & SONS, INC.New York • Chichester • Weinheim • Brisbane • Singapore • TorontoCopyright © 2000 by John Wiley & Sons, Inc.speeddigital systems at the platform level. The book walks the reader through everyrequired concept, from basic transmission line theory to digital timing analysis, high-speedmeasurement techniques, as well as many other topics. In doing so, a unique balancebetween theory and practical applications is achieved that will allow the reader not only tounderstand the nature of the problem, but also provide practical guidance to the solution.The level of theoretical understanding is such that the reader will be equipped to see beyondthe immediate practical application and solve problems not contained within these pages.Much of the information in this book has not been needed in past digital designs but isabsolutely necessary today. Most of the information covered here is not covered in standardcollege curricula, at least not in its focus on digital design, which is arguably one of the mostsignificant industries in electrical engineering.The focus of this book is on the design of robust high-volume, high-speed digital productssuch as computer systems, with particular attention paid to computer busses. However, thetheory presented is applicable to any high-speed digital system. All of the techniquescovered in this book have been applied in industry to actual digital products that have beensuccessfully produced and sold in high volume.Practicing engineers and graduate and undergraduate students who have completed basicelectromagnetic or microwave design classes are equipped to fully comprehend the theorypresented in this book. At a practical level, however, basic circuit theory is all thebackground required to apply the formulas in this book.
上傳時間： 2013-10-26
上傳用戶：縹緲
Finite state machines are widely used in digital circuit designs. Generally, when designing a state machine using an HDL, the synthesis tools will optimize away all states that cannot be reached and generate a highly optimized circuit. Sometimes, however, the optimization is not acceptable. For example, if the circuit powers up in an invalid state, or the circuit is in an extreme working environment and a glitch sends it into an undesired state, the circuit may never get back to its normal operating condition.
標簽： Creating Machines Mentor State
上傳時間： 2013-10-08
上傳用戶：wangzhen1990
