為滿足無線網絡技術具有低功耗、節點體積小、網絡容量大、網絡傳輸可靠等技術要求，設計了一種以MSP430單片機和CC2420射頻收發器組成的無線傳感節點。通過分析其節點組成，提出了ZigBee技術中的幾種網絡拓撲形式，并研究了ZigBee路由算法。針對不同的傳輸要求形式選用不同的網絡拓撲形式可以盡大可能地減少系統成本。同時針對不同網絡選用正確的ZigBee路由算法有效地減少了網絡能量消耗，提高了系統的可靠性。應用試驗表明，采用ZigBee方式通信可以提高傳輸速率且覆蓋范圍大，與傳統的有線通信方式相比可以節約40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This Paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上傳時間： 2013-10-09
上傳用戶：robter
提出了一種以ARM微處理器為控制核心的遠程無線視頻監控終端的設計方案，其監控終端的硬件設計包括視頻采集處理、中央管理控制、無線傳輸3個模塊。并給出了監控終端的軟件開發平臺和開發模式的系統啟動代碼、嵌入式Linux系統移植以及驅動程序和應用程序。測試結果表明，該監控終端設計方案合理、有效，基本滿足監控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this Paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
上傳時間： 2013-11-13
上傳用戶：wanqunsheng
This white Paper discusses how market trends, the need for increased productivity, and new legislation have accelerated the use of safety systems in industrial machinery. This TÜV-qualified FPGA design methodology is changing the paradigms of safety designs and will greatly reduce development effort, system complexity, and time to market. This allows FPGA users to design their own customized safety controllers and provides a significant competitive advantage over traditional microcontroller or ASIC-based designs. Introduction The basic motivation of deploying functional safety systems is to ensure safe operation as well as safe behavior in cases of failure. Examples of functional safety systems include train brakes, proximity sensors for hazardous areas around machines such as fast-moving robots, and distributed control systems in process automation equipment such as those used in petrochemical plants. The International Electrotechnical Commission’s standard, IEC 61508: “Functional safety of electrical/electronic/programmable electronic safety-related systems,” is understood as the standard for designing safety systems for electrical, electronic, and programmable electronic (E/E/PE) equipment. This standard was developed in the mid-1980s and has been revised several times to cover the technical advances in various industries. In addition, derivative standards have been developed for specific markets and applications that prescribe the particular requirements on functional safety systems in these industry applications. Example applications include process automation (IEC 61511), machine automation (IEC 62061), transportation (railway EN 50128), medical (IEC 62304), automotive (ISO 26262), power generation, distribution, and transportation. 圖Figure 1. Local Safety System
上傳時間： 2013-11-14
上傳用戶：zoudejile
The standard that governs the design of avioniccomponents and systems, DO-254, is one of the mostpoorly understood but widely applicable standardsin the avionic industry. While information on thegeneral aspects of the standard is easy to obtain, thedetails of exactly how to implement the standard aresketchy. And once an entity develops a process thatachieves compliance, the details of how compliancewas achieved become part of the intellectualproperty of that entity. This white Paper focuses onthe details of developing a DO-254 compliantprocess for the design of FPGAs.
上傳時間： 2013-11-03
上傳用戶：ysystc670
One of the most misunderstood constructs in the Verilog language is the nonblockingassignment. Even very experienced Verilog designers do not fully understand how nonblockingassignments are scheduled in an IEEE compliant Verilog simulator and do not understand whenand why nonblocking assignments should be used. This Paper details how Verilog blocking andnonblocking assignments are scheduled, gives important coding guidelines to infer correctsynthesizable logic and details coding styles to avoid Verilog simulation race conditions
上傳時間： 2013-11-01
上傳用戶：xzt
In this Paper, we discuss efficient coding and design styles using verilog. This can beimmensely helpful for any digital designer initiating designs. Here, we address different problems rangingfrom RTL-Gate Level simulation mismatch to race conditions in writing behavioral models. All theseproblems are accompanied by an example to have a better idea, and these can be taken care off if thesecoding guidelines are followed. Discussion of all the techniques is beyond the scope of this Paper, however,here we try to cover a few of them.
標簽： Efficient Verilog Digital Coding
上傳時間： 2013-11-23
上傳用戶：我干你啊
本文論述了狀態機的verilog編碼風格,以及不同編碼風格的優缺點，Steve Golson's 1994 Paper, "State Machine Design Techniques for Verilog and VHDL" [1], is agreat Paper on state machine design using Verilog, VHDL and Synopsys tools. Steve's Paper alsooffers in-depth background concerning the origin of specific state machine types.This Paper, "State Machine Coding Styles for Synthesis," details additional insights into statemachine design including coding style approaches and a few additional tricks.
標簽： Synthesis Machine Coding Styles
上傳時間： 2013-10-12
上傳用戶：sardinescn
Field Programmable Gate Arrays (FPGAs) are becoming a critical part of every system design. Many vendors offer many different architectures and processes. Which one is right for your design? How do you design one of these so that it works correctly and functions as you expect in your entire system? These are the questions that this Paper sets out to answer.
上傳時間： 2013-10-22
上傳用戶：lmq0059
針對嵌入式機器視覺系統向獨立化、智能化發展的要求，介紹了一種嵌入式視覺系統--智能相機。基于對智能相機體系結構、組成模塊和圖像采集、傳輸和處理技術的分析，對國內外的幾款智能相機進行比較。綜合技術發展現狀，提出基于FPGA+DSP模式的硬件平臺，并提出智能相機的發展方向。分析結果表明，該系統設計可以實現脫離PC運行，完成圖像獲取與分析，并作出相應輸出。 Abstract: This Paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the Paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上傳時間： 2013-11-14
上傳用戶：無聊來刷下
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This Paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上傳時間： 2013-11-19
上傳用戶：neu_liyan
